background image

Read these instructions thoroughly before installing, connecting, or using the 
J-FORCE nozzle. If any questions remain, call JETSTREAM at (800) 231-8192 or 
(832) 590-1300. Also read the yellow JETSTREAM SAFETY WARNING pamphlet 
included with the shipment of your new J-FORCE nozzle and reproduced inside 
this publication. This product is sold with the understanding that the purchaser 
agrees to thoroughly train all operators and maintenance personnel in the correct 
and safe installation, operation and maintenance of the product and to provide 
adequate supervision of personnel at all times. Retain these instructions for future 
reference. If this product is resold or otherwise conveyed, purchaser must pass on 
the instructions to the new user.

PRODUCT INSTRUCTIONS 
3” J-FORCE™
JF3X15 (PN 67859)
JF3X22 (PN 67860, 67861, 67862, 67863, 67864)
PI-198

The 3” J-Force

TM

 is a self-powered rotating nozzle designed to easily 

navigate and clean 3” pipes with up to 90° bends. The 3” J-Force has 
front, side, and rear jets that clear blockages, clean, and provide thrust 
to propel the tool down the pipe. The nozzle comes equipped with an 
eddy-current braking system which controls rotation speed for maximum 
cleaning power and minimum wear. 

Summary of Contents for 3" J-FORCE JF3X15









































Reviews: