background image

Jets™ Opal Wall Toilet 

Tel. +47 70 03 91 00

www.jetsgroup.com

Product No. TO615PO

Doc. Rev.: 4 (2019-01-18)

8

Service and Maintenance

Out of Use

The following procedures are to be followed if a toilet is to be out of use over a longer period of time (i.e. for cabins and recreational houses).

1. Close the water supply to the toilet.
2. Activate the release button to run a flush cycle, emptying the toilet of water.
3. The electronic bidet seat and cover must be unplugged and drained of water. Refer to the manufacturers operating manual for step by step 

procedures for when the seat and cover will be out of use for extended periods of time.

4. CAUTION: This toilet is not intended for use in temperatures below freezing without appropriate antifreeze measures being taken. For 

locations where freezing may occur, certain protection measures must be taken. For further information contact Jets Vacuum AS or your 
nearest supplier for a copy of technical information regarding freezing protection measures.

5. CAUTION: Never use automotive antifreeze (ethylene glycol) in the toilet system.
6. Turn off the power.

NOTE: Failure to adequately protect the toilet system from damages may result in void of your warranty coverage. 

NOTE: Jets Vacuum AS reserves the right to deny any warranty claim submitted if the claim is caused by freezing damage.  

Cleaning Instructions

1. Mild soap or biological cleaners are recommended for cleaning the toilet bowl. See Jets™ product range for suitable cleaning solutions.
2. Do not use cleaners that create foam.
3. The toilet is to be cleaned regularly to maintain hygiene. Also note that maintaining water in the toilet bowl will prevent odors.
4. Do not use drain cleaner, bleach or other caustic cleaners. These types of cleaners can damage components in the toilet system and damage 

the seat and cover.

5. For mineral scale buildup, we recommend use of Jets Vacuum AS biological descale products. Contact your Jets Vacuum AS supplier for 

information.

6. The electronic bidet seat and cover is an electric appliance. Be careful not to let water seep inside or leave detergent in the gap between the 

main unit and toilet bowl. When using a toilet cleaner to clean the toilet bowl, wash it off within 3 minutes and leave the toilet seat and toilet lid
open. Wipe off any cleaner that remains on the toilet bowl. If vapor from a toilet cleaner enters the main unit, it may cause a malfunction of the 
seat and cover. Wipe the back of the seat and cover with a soft cloth tightly wrung out with water.

Spare Parts and Accessories

Available spare parts are indicated in the component list for the toilet. Spare parts and accessories can be ordered via your local Jets Vacuum AS 
supplier. For multi-toilet installations, a complete recommendation for spare parts is available. Contact your Jets Vacuum AS supplier for details. 

Service and Maintenance

Jets Vacuum AS provides all customers with 24 hour worldwide technical assistance. For urgent  matters please contact Jets Vacuum AS service 
department directly at +47 70039100. For other matters, please contact your nearest Jets Vacuum AS supplier. 

1. Disassembly of the toilet must be carried out by a licensed professional.  
2. All local, state and federal regulations regarding water barriers and plumbing must be adhered to. 
3. Refer to the individual product data sheets for more specific information. Refer to the products troubleshooting information for general 

maintenance. 

4. It is recommended that service and maintenance routines be carried out in accordance with the information in this document.

When making enquiries, please have the following information available. 

1. Toilet model number.
2. For valve enquiries: Valve serial number (the serial number identification is located on the label applied to the valve).
3. Part number, description, quantity (see the product component list for details).

Locating a Water Leak

Make a practice of regularly checking around the toilet, piping and pump for any signs of a water leak. Check for wetness, mold or foul smells, as 
that might indicate a leak.

If you suspect a leak anywhere in your plumbing system, call in a professional to make a repair as soon as possible. 

Summary of Contents for Opal Wall Toilet TO615PO










Reviews: