background image

 

40

16.0

  Warranty and Service 

JET

®

 warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please 

contact

 

Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. 

Warranty Period

 

The general warranty lasts for the time period specified in the literature included with your product or on the official 
JET branded website.  

 

JET products carry a limited warranty which varies in duration based upon the product. (See chart below) 

 

Accessories carry a limited warranty of one year from the date of receipt. 

 

Consumable items are defined as expendable parts or accessories expected to become inoperable within a 
reasonable amount of use and are covered by a 90 day limited warranty against manufacturer’s defects. 

Who is Covered 

This warranty covers only the initial purchaser of the product from the date of delivery. 

What is Covered 

This warranty covers any defects in workmanship or materials subject to the limitations stated below. This warranty 
does not cover failures due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-and-tear, 
improper repair, alterations or lack of maintenance. 

Warranty Limitations 

Woodworking products with a Five Year Warranty that are used for commercial or industrial purposes default to a 
Two Year Warranty. Please contact Technical Service at 1-800-274-6846 for further clarification.

 

How to Get Technical Support 

Please contact Technical Service by calling 1-800-274-6846. 

Please note that you will be asked to provide proof 

of initial purchase when calling. 

If a product requires further inspection, the Technical Service representative will 

explain and assist with any additional action needed.

 

JET has Authorized Service Centers located throughout the 

United States. For the name of an Authorized Service Center in your area call 1-800-274-6846 or use the Service 
Center Locator on the JET website.

 

More Information 

JET is constantly adding new products. For complete, up-to-date product information, check with your local distributor 
or visit the JET website. 

How State Law Applies 

This warranty gives you specific legal rights, subject to applicable state law.  

Limitations on This Warranty 

JET LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR EACH PRODUCT. 
EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A 
PARTICULAR PURPOSE ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN 
IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. 
 
JET SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR 
INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR 
PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR 
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. 
 
JET sells through distributors only. The specifications listed in JET printed materials and on official JET website are 
given as general information and are not binding. JET reserves the right to effect at any time, without prior notice, 
those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason 
whatsoever. JET

®

 branded products are not sold in Canada by JPW Industries, Inc. 

Product Listing with Warranty Period  

90 Days – Parts; Consumable items; Light-Duty Air Tools 
1 Year – Motors; Machine Accessories; Heavy-Duty Air Tools; Pro-Duty Air Tools 
2 Year – Metalworking Machinery; Electric Hoists, Electric Hoist Accessories 
5 Year – Woodworking Machinery 
Limited Lifetime – JET Parallel clamps; VOLT Series Electric Hoists; Manual Hoists; Manual Hoist   
Accessories; Shop Tools; Warehouse & Dock products; Hand Tools 

 
NOTE:  JET is a division of JPW Industries, Inc. References in this document to JET also apply to JPW Industries, 
Inc., or any of its successors in interest to the JET brand. 

 

 

 

Summary of Contents for ProShop II JPS2-115













































Reviews: