Jet JJ-6CSDX Operating Instructions And Parts Manual Download Page 6 | Manualshive

Page: 6 / 44

background image

6

Familiarize yourself with the following safety notices used in this manual:

This means that if precautions are not heeded, it may result in minor injury and/or

possible machine damage.

This means that if precautions are not heeded, it may result in serious injury or possibly

even death.

- - SAVE THESE INSTRUCTIONS - -

On-Off Switch Padlock

The jointer is equipped with a push-button
switch that will accept a safety padlock (see
figure – not included). To safeguard your
machine from unauthorized operation and
accidental starting by young children, the use of
a padlock is highly recommended. JET model
PD-LK-1 (Stock No. 709012) is available from
your local authorized JET distributor or by calling
JET Equipment & Tools at the phone number on
the cover of this manual.

Model PD-LK-1 On-Off Switch Padlock

Introduction

This manual is provided by WMH Tool Group covering the safe operation and maintenance procedures
for Models JJ-6CSX, JJ-6CSDX and JJ-6HHDX Jointers. This manual contains instructions on
installation, safety precautions, general operating procedures, maintenance instructions and parts
breakdown. This machine has been designed and constructed to provide years of trouble free operation if
used in accordance with instructions set forth in this manual. If there are any questions or comments,
please contact your local supplier or WMH Tool Group, or visit our web site: www.jettools.com.

«
...
4
5
6
7
8
...
»

Summary of Contents for JJ-6CSDX













































Reviews:

No comments

Related manuals for JJ-6CSDX

Brand: Gage Bilt Pages: 9

Brand: Gage Bilt Pages: 13

Brand: Gage Bilt Pages: 24

Brand: Hama Pages: 24

Brand: JBM Pages: 12

Brand: JAMEC PEM Pages: 4

Brand: Xaoc Devices Pages: 8

PDSP 1000 A1 SANDBLASTER GUN

Brand: Parkside Pages: 51

Brand: Parkside Pages: 56

Brand: Zhaoxin Pages: 5

Brand: Campbell Hausfeld Pages: 32

Brand: Eastwood Pages: 20

Brand: Gianni Pages: 6

Brand: Jet Pages: 32

Brand: Echo Pages: 24

Brand: Oemtools Pages: 4

Brand: BGS technic Pages: 8

Brand: Moser Systemelektrik Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands