manualshive.com logo in svg

jenway 7310, Operating Manual

Share
Download
jenway 7310 Operating Manual Download Page 81

Kinetics 

 

Start kinetics measurement

Kinetics 

 

Kinetics measurement in progress

Kinetics 

 

Sigma icon - Post measurement statistics

Kinetics 

 

Kinetics moving line

Kinetics 

 

Update factor in settings

Kinetics 

 

Toggle icon – switches between the initial and final point lines

Kinetics 

 

Double less than icon - Decrease the time by 5 seconds intervals 

Kinetics 

 

Single less than icon - Decrease the time by 1 second intervals

Kinetics 

 

Double greater than icon - Increase the time by 5 seconds intervals

Kinetics 

 

Single greater than icon - Increase the time by 1 second intervals  

Kinetics 

 

Data point interval – used in print settings

Accessories   

No single cell - Method created on a unit with a single cell accessory    

 

 

fitted

Accessories   

8 cell turret icon – the automatic 8 cell turret is in use

Accessories   

Error finding cell position 0 on turret

Accessories   

No turret - Method created on a unit with a turret accessory fitted 

Accessories        

°C

 

Degrees Celsius

Accessories        

°F

 

Degrees Fahrenheit

Accessories         

Peltier accessory in use – current temperature is below set point. 

 

 

The current temperature is displayed above set point temperature

Accessories   

No peltier - Method created on a unit with a peltier accessory fitted

Accessories   

Sipper pump in use – running in forward direction 

Accessories   

Sipper pump in use – running in reverse direction

Accessories   

Timed sipper pump

Accessories   

Timed sipper pump calibration sequence

Accessories   

Start sipper pump – enables take up time to be set

83

Summary of Contents for 7310























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands