manualshive.com logo in svg

jenway 7310, Operating Manual

Share
Download
jenway 7310 Operating Manual Download Page 24

26

The 

toggle

 icon enables the large primary display to be set to show the absorbance or % transmittance. 

To change the primary and secondary displays press the key adjacent to the 

toggle

 icon. Repeat presses 

will cycle the displays between absorbance or % transmittance.

5.2.1 

Selecting a Wavelength

The wavelength can be adjusted in the expanded operating menu by using the keys adjacent to the 

arrow

 icons to increase or decrease the wavelength. Once the required wavelength has been selected 

a calibration can be performed.

5.3        CALIBRATION

The  calibration  must  be  performed  at  the  same 
wavelength at which the sample will be measured. Insert 
a cuvette containing the blank solution into the sample 
chamber and close the instrument lid. Press the key below 
the 

calibrate  to  zero  absorbance

  icon.  This  sets  the 

instrument to zero absorbance and 100% transmittance.

Once the calibration is complete the 

measure sample

 icon appears and the sample can be measured. 

If the wavelength is adjusted before a sample is measured the 

measure sample

 icon will disappear and 

the instrument must be calibrated again at the new wavelength.

5.4    

SAMPLE MEASURMENT

It is not possible to measure a sample before the instrument 
has been calibrated at the selected wavelength. Once the 
calibration  has  been  performed  the 

measure  sample

 

icon is displayed and a sample can be measured. Remove 
the  cuvette  containing  the  blank  solution  and  place  a 
cuvette  containing  the  sample  to  be  measured  in  the 
sample holder. Close the instrument lid and press the key 
below the 

measure sample

 icon. 

Once the measurement is complete the photometric result will be shown on the screen. Subsequent 
samples can be measured in the same way. If the wavelength is adjusted between sample measurements 
then the instrument must be calibrated again before more samples can be measured.

100.0

0.000

400

09:02

%T

ABS

nm

81.7

0.088

400

09:02

%T

ABS

nm

Summary of Contents for 7310























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands