background image

 

E-9 

Wake to Radio (only for FM) - Turning the “wake to” Radio ON: 

 

The Radio will automatically turn on when the alarm time is reached. The 
corresponding RADIO 1 or RADIO 2 indicator will flash.

 

 

The unit will start playing the last FM radio station you listened to when the alarm 
time is reached, so make sure the station is set to the one you 

want to wake up to

.

 

  The volume level will start out low and gradually increase to maximum volume. 
  Press the SNOOZE BUTTON (#5) to temporarily turn off the radio, or 

press the 

STANDBY   / SOURCE / ALARM OFF BUTTON (#8) to turn the radio off.  

  If no buttons are pressed when the radio is playing, it will continue playing for 60 

minutes and then turn off automatically. 

 

Review the Alarm time setting: 

In standby mode, tap the VOL - / ALARM 1 BUTTON (#6) or VOL + / ALARM 2 
BUTTON (#7) once. The corresponding alarm indicator and alarm time will be flashing 
on the display. The unit will automatically return to standby mode if no buttons are 
pressed within 5 seconds.  

 
Turning the daily alarms OFF:  

  In Standby mode, repeatedly tap the 

VOL - / ALARM 1 BUTTON

 (#6) to step 

through the “wake to” options shown on the left side of the display.  
Alarm 1 -> Radio 1 - > OFF (all indicators off and returns to the current time) 

  The ALARM 1 time will flash on the display as you step through the options. 
  All ALARM 1 options are disabled when the indicators are off and the current time 

is showing on the display.   

  Turning off ALARM 2 will follow the same steps as ALARM 1 above, but you will be 

using the 

VOL + / ALARM 2 BUTTON

 (#7) and the ALARM 2 indicators will be on 

the right side of the display. 

 

Notes: 

  For setting a one-day alarm, set the desired alarm time the day before following the 

Setting the alarms

” section above. 

  The alarm will sound the next day at the set alarm time.  

  After turning off the alarm, follow the “

Turning the daily alarms OFF

” section 

above to prevent the alarm from sounding again the next day.  

 
 

SNOOZE FUNCTION 

 

When  the  alarm  sounds,  tap  the  SNOOZE  BUTTON  (#5)  to  temporarily  turn  off  the 
alarm  and  activate  the  snooze  function.  The  alarm  will  stop  and  turn  on  again  9 
minutes later. This can be repeated when the alarm sounds again. 

 

Notes: 

 The corresponding AL1 or AL2 alarm indicator will 

flash 

during the snooze period. 

 To  cancel  the  snooze  period  and  the  alarm,  press  the  STANDBY   /  SOURCE  / 

ALARM OFF BUTTON (#8). 

 
 
 
 
 
 
 

Summary of Contents for JCR-206















Reviews: