background image

CD3720XM

17

Troubleshooting

Reset

After removing the front panel, use a pencil tip (or any non-metallic object) to press 

RESET

 

(20).

Remove Radio From Dash

To remove the radio from the dash, detach the 
front panel and remove the trim ring by gently 
pulling up in the middle to release the plastic 
snaps. Insert removal keys between the radio 
chassis and sleeve to depress locking 
springs. Pull the radio out of the dash.

Problem

Cause

Corrective Action

Does not operate 
(display does not light)

No power to yellow wire; no 
power to red wire

Check connection with test light; 
check vehicle fuse with test light

Inline fuse blown

Replace fuse

No power to unit

Inline fuse blown

Check/replace fuse

No speakers operate 
(display lights normally)

Speaker harness not 
connected

Connect speaker harness; check 
speaker wires

Not all speakers 
operate

Incorrect splices or 
connections

Check all splices and connections

Speaker wires shorting to 
chassis ground or to each 
other

Check splices, insulate all bare wires

Blows fuses

Power wire shorting to 
ground

Make sure wire is not pinched

Speaker wires shorting to 
ground

Make sure wire is not pinched

Incorrect fuse/fuse too small

Install fuse of correct rating

Error-1 (CD Player)

Mechanism error

Press 

RESET

, insert disc and try 

again

Error-2 (CD Player)

Servo error

Press 

RESET

, insert disc and try 

again

CD skips too much

Receiver mount is not solid 
or backstrap is not secure

Check mounting and backstrap, 
tighten if needed

Specifications

CEA Power Ratings

Power Output. . . . . . . . . . . . . . . . . . . . . . . . . . . 16 watts RMS X 4 channels into 4-ohms @ < 1% THD+N
Signal to Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . .  70dBA below reference. (Reference: 1 watt, 4-ohms)
Dynamic Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  32 watts @ 4-ohms x 4 channels
Frequency Response. . . . . . . . . . . . . . . . 20Hz to 20kHz (-3dB), Auxiliary input used as source reference
Reference Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.4VDC 

CD Player

Signal to Noise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  >90 dB
Frequency Response. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Hz to 20kHz, -3 dB
Channel Separation @ 1kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  >55 dB
D/A Converter  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Bit/CH

FM Tuner

Tuning Range  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87.5MHz – 107.9MHz
FM Mono Sensitivity  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 dBf
50 dB Quieting Sensitivity (stereo)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 dBf
Stereo Separation @ 1kHz  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  >35 dB
Frequency Response. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Hz to 12kHz, -3dB

AM Tuner

Tuning Range  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530kHz – 1710kHz
AM Sensitivity  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30uV
Frequency Response. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30Hz to 2kHz, -3dB

Auxiliary Input 

Input Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400mV RMS for 1 watt RMS into 4-ohms
Frequency Response. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Hz to 20kHz, -3dB
Input Impedance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  10k-ohms

General

Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  11 – 16 VDC, negative ground
Fuse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 amp fast blow ATO
Wire Harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  20-pin quick-disconnect
Dimensions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7" x 7" x 2" (178mm x 178mm x 51mm)

Specifications subject to change without notice.

Summary of Contents for CD3720XM





















Reviews: