background image

3

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Tools needed

 

Tape measure

 

1/4" (6.35 mm) nut driver

 

#2 Phillips screwdriver

 

Marker or pencil

 

Pliers

 

Flat-blade screwdriver

Parts supplied

 

Foam strip roll

 

Clamping brackets (2)

 

2

1

/

2

" (6.4 cm) clamping screws (2)

 

Drip tray

 

Mounting bridge kit: W11031680

Parts needed

 

A UL Listed or CSA Approved connector for 1/2" (1.3 cm) 

diameter conduit

 

UL Listed wire connectors

Check local codes. Check existing electrical supply. See the 

“Electrical Requirements” section.
It is recommended that all electrical connections be made by 

a licensed, qualified electrical installer.

Location Requirements

IMPORTANT:

 Observe all governing codes and ordinances. 

When installing cooktop, use minimum dimensions given.

 

The cooktop must be a specified cooktop that is approved 

to be installed either alone or over an undercounter built-in 

oven. Check the cooktop base for an approved installation 

label. If you do not find this label, contact your dealer to 

confirm that your cooktop is approved.

 

The cooktop must be installed in a level countertop. 

 

To eliminate the risk of burns or fire by reaching over the 

heated surface units, cabinet storage space located above 

the surface units should be avoided. If cabinet storage 

is to be provided, the risk can be reduced by installing a 

range hood or microwave hood combination that projects 

horizontally a minimum of 5" (12.7 cm) beyond the bottom 

of the cabinets.

 

Ovens approved for this type of installation will have an 

approval label located on the top of the oven. If you do 

not find this label, contact your dealer to confirm that your 

oven is approved. Refer to oven manufacturer’s Installation 

Instructions for approval for built-in undercounter use and 

proper cutout dimensions. 

 

The cooktop should be installed away from strong draft 

areas, such as windows, doors, fans, or strong heating 

vents. The cooktop should be located for convenient use 

in the kitchen.

 

Use the countertop opening dimensions that are given 

with these Installation Instructions. Given dimensions are 

minimum clearances and provide 0" (0 cm) clearance.

 

Grounded electrical supply is required. See the “Electrical 

Requirements” section.

IMPORTANT:

 To avoid damage to your cabinets, check with 

your builder or cabinet supplier to make sure that the materials 

used will not discolor, delaminate, or sustain other damage. This 

cooktop has been designed in accordance with the requirements 

of UL and CSA International and complies with the maximum 

allowable wood cabinet temperatures of 194°F (90°C).

Product Dimensions

A

B

D

F

E

C

G

A.  15" (38.1 cm)
B.  21" (53.3 cm)
C. 14

19

/

64

" (36.3 cm)

D. 20

19

/

64

" (51.5 cm)

E. 4

1

/

4

" (10.8 cm)

F. 5

1

/

2

" (14.0 cm)

G. 1

1

/

4

" (3.2 cm)

Summary of Contents for JEF3115GS

















Reviews: