background image

6

1. 

Remove the foam strip from the hardware package. Remove 

the backing from the foam strip. 

For countertop installations: 

Apply the foam strip with the 

adhesive side to the countertop within 1/16" (1.6 mm) of the 

edge of the cutout, front, back, and sides.

For flush installations:

 Apply the foam strip with the 

adhesive side to the bottom of the cutout recessed area. 

Save the excess foam strip for use with the mounting 

bridge kit.

NOTE:

 The foam strip helps keep the underside of the 

cooktop frame free from debris and helps the cooktop 

sit flat on uneven countertops. Do not silicone seal in place.

Install Cooktop

NOTE:

 For multi-unit installations, a mounting bridge kit is 

required. See the “Tools and Parts” section.

1. 

Install the cooktop into the countertop cutout by tilting one 

end of the cooktop into the cutout, then lowering the other 

end into the cutout.

NOTE:

 Make sure that the front edge of the cooktop is 

parallel to the front edge of the countertop. If repositioning 

is needed, lift the entire cooktop up to avoid scratching the 

countertop.

2. 

Place drip tray in the well at the front of the griddle. Slide tray 

toward the back until it stops.

3. 

Clean griddle before using. Refer to the Use and Care Guide.

Install cooktop into countertop

1. 

Remove the two hold-down screws located in each side of 

the cooktop burner box.

2. 

Attach the two hold-down brackets to the burner box.

3. 

Install the cooktop into the countertop cutout by tilting one 

end of the cooktop into the cutout, then lowering the other 

end into the cutout.

4. 

Start the hold-down screws into the hold-down brackets.

5. 

Center the cooktop in the opening and, using a wood block 

between the screw and the countertop, moderately tighten 

the screws to secure cooktop.

IMPORTANT:

 Do not tighten screws directly against the 

countertop.

Make Electrical Connection

This cooktop is manufactured with a frame-connected green or 

bare ground wire. Connect the cooktop cable to the junction box 

through the UL Listed or CSA Approved conduit connector.

Electrical Connection Options

If Your Home Has: And You Will Be 

Connecting to:

Go to Section:

4-wire direct

A fused disconnect 

or circuit breaker 

box

4-Wire Cable from 

Power Supply to 

4-Wire Cable from 

Cooktop

(12.7 cm)

5"

3-wire direct

A fused disconnect 

or circuit breaker 

box

3-Wire Cable from 

Power Supply to 

4-Wire Cable from 

Cooktop

(8.9 cm)

3

¹⁄₂

"

A
B
C
D

A. Countertop
B.  Foam strip

C. Cutout
D.  1/16" (1.6 mm)

B

A

A.  Griddle drip tray
B. Griddle

A

B

C

E

D

A. Countertop
B.  Wood block
C.  Hold-down screw
D.  Hold-down bracket
E.  Burner box

WARNING

Electrical Shock Hazard

Disconnect power before servicing.
Use 8 gauge copper wire.
Electrically ground cooktop.
Failure to follow these instructions can result in death, 

fire, or electrical shock.

Summary of Contents for JEF3115GS

















Reviews: