background image

Vertical

Shaft

Up&Down

To Clamp

Button

Baffle

Extension

Manual

Feeding

Switch

Blowing

Button

RETURN

“Moving up and down of vertical shaft”: The vertical shaft will move down after pressing this key and 

the vertical shaft will move up after pressing this key again.

“Taking button by operating button clamp”: Button clamp will be unfolded after pressing this key and 

the button clamp will be folded after pressing this key again.

“Stretching  out  and  drawing  back  of  damper”:  The  damper  will  stretch  out  to  block  the  button

from moving, and the damper will draw back and button can freely move after pressing this key again. 

“Manually feeding button”: The engine arm will feed button once after pressing this key.

“Feeding button by blowing gas”: Button feeding will be conducted once by blowing gas after pressing

this key.

“Back”: Return to the precious page after pressing this key.

J9 pressure regulating valve by gas blowing: When buttons are delivered to button feeding track at the vibrating plate,

feed the buttons at the gripper arm through gas blowing, and the recommended air pressure is between 0.3-0.35Mpa.

3

Manually Feeding: Press this key for manually repairing button when there is no button in the gripper.

Thickness Measurement: Pressing this key, lift the pressing plate for measuring thickness, take one button to 

be used and place it on the plate, and then release this key.

Summary of Contents for JM-988



















Reviews: