manualshive.com logo in svg

JEM Roadie Compact, User Manual, Page: 13 / 24

Share
Download
JEM Roadie Compact User Manual Download Page 13

 Control 

settings 

13 

 

 

S e t t i n g   F o g   d e n s i t y  

Use the Menu Previous / Next buttons to select the 

&/'

 option. 

Use the Up/Down buttons to select the density from 

 – 

. 

Press the Enter button to store the fog setting. The display shows 

3%4

. 

 
The machine will only produce fog if the Timer or Continuous switches are On. 
(Or, if using the digital remote, if you press the Timer or Fog buttons). 

 

If you want to temporarily change the fog density, do not press Enter. 
The fog setting will go back to its stored value next time the machine 
is powered up. This applies to all options. 

 
If a long burst of fog is produced, after a time the fog density will be 
automatically reduced to keep the machine temperature within the operating 
range. This allows continuous operation, so that the machine does not have to 

stop and re-heat. 

S e t t i n g   F a n   s p e e d  

Use the Previous / Next buttons to select the 

&!.

 option. 

Use the Up/Down buttons to select the fan speed from 

 – 

. 

Press the Enter button to store the fan setting. 
 

The fan will run continuously if set above 0% and the Fan, Timer or Continuous 
switches are On. (Or, if using the digital remote, if the RUN menu is set to FAN, 
TIME or CONT). 
 
If fog is being produced and the fan is off or set to a low speed, the fan speed 

will be automatically increased to prevent buildup of fog at the machine output. 
 

S e t t i n g   t h e   T i m e r  

If smaller amounts of fog are required the machine has an automatic timer to 
give timed bursts of fog. You can set the “Run” and “Off” times independently 

between 1 and 90 seconds. 
 
Use the Previous / Next buttons to select the 

415.

 or 

4/&&

 option. 

Use the Up/Down buttons to select the run or off time from 

 seconds to 

 

seconds. If you hold down the button the time will count up or down, getting 

faster the longer you hold it. 
Press the Enter button to store the timer setting. 
 
To enable timer mode, switch on the Timer switch (or, if using the digital remote, 
press the Timer button). 

 

When the timer is running and the display is not showing a menu, the 
display shows a countdown for the run time (RU--) and the off time 
(OF--). 

 
 
 

 

Summary of Contents for Roadie Compact

























Reviews:

No comments