7. Montage der Türverkleidung
7.1. Türverkleidung oben in die Türschachtleiste einhängen
7.2. In umgekehrter Reihenfolge wie auf Seite 3 beschrieben wieder befestigen.
7.3. Regenschutzfolie für die Tieftöner u-förmig einschneiden und seitliche
Schnittkanten zur Vermeidung von Vibrationsgeräuschen der Folie
stabilisieren (z.B. mit Packband)
1. Zur Positionierung der Befestigungspunkte 1-11 das passgenau ausgerichtete
Paneel als Schablone verwenden:
•
Markierung Befestigungspunkt 1-6_ bereits im Paneel montiert:
durch Aufdrücken des Paneels auf der Türververkleidung - Abdruck sichtbar
• Markierung der Befestigungspunkte 7-11:
mit einem dünnen Vorstecher auf der Türverkleidung markieren.
2. Die Lautsprecheröffnungen auf der Türverkleidung anzeichnen.
3. Paneel wieder abnehmen. Die angezeichneten Lautsprecheröffnungen
auf der Türverkleidung mit einer Stichsäge ausschneiden.
4. Für die einzusetzenden Schrauben die Bohrungen gemäß Markierungen
mit einem 6mm-Bohrer vornehmen.
5. Mitgelieferte M4-Schrauben eindrehen. Türpaneel mit der Türver-
kleidung durch leichtes Festschrauben aller 11x M4-Schrauben fixieren.
Alle Schrauben mit den Unterlagscheiben und Muttern sichern.
6. Nochmals Passgenauigkeit überprüfen und Schrauben festziehen:
Alle Schnittkanten des Paneels müssen umlaufend ohne Spalt
auf der Türverkleidung anliegen.
4. Bearbeitung der Türverkleidung / Montage der Türpaneele
75151 - Audi A 4
Cabrio
- 9 -
© JEHNERT SOUND DESIGN
75151 - Audi A 4
Cabrio
- 6 -
© JEHNERT SOUND DESIGN
�
M 4 x30
montiert
M 4 x50
montiert
M 4 x50
montiert
M 4 x50
montiert
M 4 x40
montiert
M 4 x20
montiert
✍
✍
1
2
3
4
5
7
9
10
8
M 4 x 20
M 4 x 20
M 4 x 30
M 4 x 30
6
M 4 x 30
11
7. installation of the door-lining onto the car doors
7.1. put the door-lining into the upper sealing of the car door
7.2. fit it in contrary order of succession as described on page no. 3
7.3. cut out the moisture protection foil (u-form) and stabilize the lateral cutting
edges in order to avoid vibration noise ( e.g. use a packing tape)
1. use the precisely aligned panel as template in order to mark fastening points 1- 11:
•
marking of fixing points
1-3_ premounted in the panel:
Press the panel to the door lining makes the screw points visible
•
marking of fixing points
4-11:
use a thin awl to set the marks on the door-lining
2. draw the speakers’ cut-outs onto the door-lining.
3. remove the panel again.
cut out holes for loudspeakers along the marking with a compass saw (see fig.)
4. use a 6mm drill for the screws according to the marks set before
5. Screw in the screws supplied with. Affix the door build to the door-lining.
Screw all 8 x screws only hand-tight .
Secure all screws with the washers and nuts.
6. check again for precise fitting and tighten screws.
check all screw connections:
In order to avoid damages to the car door, check
the length of the staybolts on the backside of the door lining once again and
possibly shorten them.
All cutting edges of the panel must fit to the door lining snugly
all around without gap
4. Handling of door lining / Panel installation - Fastening
75160 - BMW 3 E 46 Coupé / Convertible - 9 -
© JEHNERT SOUND DESIGN
75160 - BMW 3 E 46 Coupé / Convertible - 6 -
© JEHNERT SOUND DESIGN
☞
✍
✍ ✍
✍ ✍
✍
1
2
3
4
5
6
7
8
9
10
11
M 4 x 40
M 4 x 50
already
mounted
M 4 x40
already
mounted
M 4 x40
already
mounted
Spax 5,0 x 70
M 4 x 30
M 4 x 50
M 4 x 50
M 4 x 40
M 4 x 40
1-6,
7-11:
7. installation of the door-lining onto the car doors
7.1. put the door-lining into the upper sealing of the car door
7.2. fit it in contrary order of succession as described on page no. 3
7.3. cut out the moisture protection foil (u-form) and stabilize the lateral cutting
edges in order to avoid vibration noise ( e.g. use a packing tape)
1. use the precisely aligned panel as template in order to mark fastening points 1- 11:
•
marking of fixing points
1-3_ premounted in the panel:
Press the panel to the door lining makes the screw points visible
•
marking of fixing points
4-11:
use a thin awl to set the marks on the door-lining
2. draw the speakers’ cut-outs onto the door-lining.
3. remove the panel again.
cut out holes for loudspeakers along the marking with a compass saw (see fig.)
4. use a 6mm drill for the screws according to the marks set before
5. Screw in the screws supplied with. Affix the door build to the door-lining.
Screw all 8 x screws only hand-tight .
Secure all screws with the washers and nuts.
6. check again for precise fitting and tighten screws.
check all screw connections:
In order to avoid damages to the car door, check
the length of the staybolts on the backside of the door lining once again and
possibly shorten them.
All cutting edges of the panel must fit to the door lining snugly
all around without gap
4. Handling of door lining / Panel installation - Fastening
75160 - BMW 3 E 46 Coupé / Convertible - 9 -
© JEHNERT SOUND DESIGN
75160 - BMW 3 E 46 Coupé / Convertible - 6 -
© JEHNERT SOUND DESIGN
☞
✍
✍ ✍
✍ ✍
✍
1
2
3
4
5
6
7
8
9
10
11
M 4 x 40
M 4 x 50
already
mounted
M 4 x40
already
mounted
M 4 x40
already
mounted
Spax 5,0 x 70
M 4 x 30
M 4 x 50
M 4 x 50
M 4 x 40
M 4 x 40
7. installation of the door-lining onto the car doors
7.1. put the door-lining into the upper sealing of the car door
7.2. fit it in contrary order of succession as described on page no. 3
7.3. cut out the moisture protection foil (u-form) and stabilize the lateral cutting
edges in order to avoid vibration noise ( e.g. use a packing tape)
1. use the precisely aligned panel as template in order to mark fastening points 1- 11:
•
marking of fixing points
1-3_ premounted in the panel:
Press the panel to the door lining makes the screw points visible
•
marking of fixing points
4-11:
use a thin awl to set the marks on the door-lining
2. draw the speakers’ cut-outs onto the door-lining.
3. remove the panel again.
cut out holes for loudspeakers along the marking with a compass saw (see fig.)
4. use a 6mm drill for the screws according to the marks set before
5. Screw in the screws supplied with. Affix the door build to the door-lining.
Screw all 8 x screws only hand-tight .
Secure all screws with the washers and nuts.
6. check again for precise fitting and tighten screws.
check all screw connections:
In order to avoid damages to the car door, check
the length of the staybolts on the backside of the door lining once again and
possibly shorten them.
All cutting edges of the panel must fit to the door lining snugly
all around without gap
4. Handling of door lining / Panel installation - Fastening
75160 - BMW 3 E 46 Coupé / Convertible - 9 -
© JEHNERT SOUND DESIGN
75160 - BMW 3 E 46 Coupé / Convertible - 6 -
© JEHNERT SOUND DESIGN
☞
✍
✍ ✍
✍ ✍
✍
1
2
3
4
5
6
7
8
9
10
11
M 4 x 40
M 4 x 50
already
mounted
M 4 x40
already
mounted
M 4 x40
already
mounted
Spax 5,0 x 70
M 4 x 30
M 4 x 50
M 4 x 50
M 4 x 40
M 4 x 40
