P/N 960-000175R_Rev. A {EDP #233426}
© 2014, JAPAN CASH MACHINE CO., LTD.
3 2
Series Banknote Validator (DBV-400) Integration Guide
Red
(3)
Red
(1)
Stacker Motor
Lock-UP
While operating the Stacker Motor, no pulse inputs occurred greater than
the specified value.
[Solution] Check that the following parts are properly assembled and/or
Harness connected. Clean or adjust the following parts and Sensors.
[Relative Parts] Stacker Motor, Stacker Encoder.
If the error is not resolved, change the above related part or parts.
Red
(3)
Red
(2)
Pusher
Mechanism Home
Position Error
When stacking Banknotes, the Pusher Mechanism is not returning to the
Home position.
[Solution] Check that the following parts are properly assembled and/or
Harness connected. Clean or adjust the following parts and Sensors.
[Relative Parts] Pusher Mechanism, Stacker Motor, Stacker Home Sensor,
Stacker Motor Encoder.
If the error is not resolved, change the above related part or parts.
Red
(3)
Red
(3)
Banknote Jam
(Cash Box)
When transporting a Banknote in the Cash Box, the Sensors are not
detecting a Banknote present condition when the time interval is too long,
or the pulse number is greater than specified value for the function.
[Solution] Remove Banknotes from the Cash Box.
Check that the following parts are properly assembled and/or Harness
connected. Clean or adjust the following parts and Sensors.
[Relative Parts] Exit Sensor, Pusher Mechanism, Stacker Motor, Stacker
Home Sensor, Stacker Motor Encoder.
If the error is not resolved, change the above related part or parts.
Red
(3)
Red
(4)
Feed Motor Speed
Error
While Initializing, no pulse inputs exist greater than the specified value.
[Solution] Remove Banknotes from the DBV-400 Unit.
Check that the following parts are properly assembled and/or Harness
connected. Clean or adjust the following parts and Sensors.
[Relative Parts] Feed Motor, Feed Motor Encoder.
If the error is not resolved, change the above related part or parts.
Red
(3)
Red
(7)
Reserved
Contact your local JCM Representative if this error occurs.
Red
(3)
Red
(8)
Fraud Detection
Sensors detect Banknotes occurring with abnormal timing.
[Solution] Check that the following parts are properly assembled and/or
Harness connected. Clean or adjust the following parts and Sensors.
[Relative Parts] Entrance Sensor, Validation Sensor, Feed Motor and Feed
Motor Encoder.
If the error is not resolved, change the above related part or parts.
Purple
(3)
Purple
(1)
Cash Box Full
Sensors detected that the Cash Box is full.
[Solution] Remove Banknotes from the Cash Box.
Check that the following parts are properly assembled and/or Harness
connected. Clean or adjust the following parts and Sensors.
[Relative Parts] Pusher Mechanism, Stacker Motor, Stacker Home Sensor,
Stacker Motor Encoder.
If the error is not resolved, change the above related part or parts.
Purple
(3)
Purple
(2)
Cash Box Removal
The Cash Box has been removed.
[Solution] Firmly re-seat the Cash Box.
Check that the following part is properly assembled and/or Harness
connected. Clean or adjust the following Sensor.
[Relative Parts] Box Sensor.
If the error is not resolved, change the above related part or parts.
Purple
(3)
Purple
(3)
Banknote Jam
(Transport Unit)
When transporting or returning a Banknote in the Transport Unit, the
Sensors did not detect a Banknote present condition when the time interval
was too long, or the pulse number is greater than specified value for the
function.
[Solution] Check that the following parts are properly assembled and/or
Harness connected. Clean or adjust the following parts and Sensors.
[Relative Parts] Entrance Sensor, Validation Sensor, Exit Sensor, Feed
Motor, Feed Motor Encoder.
If the error is not resolved, change the above related part or parts.
Table 22
LED Flash Error Codes (Continued)
Normal
Operation
Performance
Test
Error
Causes and Solutions
LED
Sequence
LED
Sequence
