background image

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00 
www.JCBdiy.com

Engine will not start.

Engine is flooded.

 

Remove spark plug, then turn 
the unit so the spark plug hole is 
aimed at the ground. 

 

Set the choke lever to “Run” 
position and pull starter grip 10 to 
15 times. This will clear excessive 
fuel from the engine. 

 

Remove any fuel from the 
product. 

 

Clean and reinstall the spark 
plug. 

 

Clean up any spilled fuel and 
move at least 9 m away before 
restarting. 

 

Pull starter grip 3 times with the 
choke lever at “Run” position. 

 

If the engine does not start, set 
the choke lever to “Full” choke 
position and repeat the normal 
starting procedure.

 

If the engine still fails to start, 
repeat procedure with a new 
spark plug.

Engine does not stop 
when the On/Off 
switch is off.

Electrical connection is 
loose/unplugged.

 

Set the choke lever to “Full” choke 
position to stop the engine.

 

Immediately stop using the 
product.

 

Check that the electrical 
connection at the bottom of the 
trimmer is properly connected.

 

Contact a service dealer if the 
problem persists.

Engine starts but will 
not accelerate.

Not enough time given 
for the engine to warm 
up.

 

Allow the engine to completely 
warm up.

 

If the engine does not accelerate 
after 3 minutes, contact a service 
dealer.

Engine starts but 
will only run at high 
speed and at half 
choke.

Carburetor requires 
adjustment.

Contact a service dealer.

JCB-BC26_960443002-01_Manual_final.indd   A20

JCB-BC26_960443002-01_Manual_final.indd   A20

12/2/2010   5:38:02 PM

12/2/2010   5:38:02 PM

Summary of Contents for JCB-BC26

























Reviews: