background image

GENERAL SAFETY RULES

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00 
www.JCBdiy.com

INTENDED USE

This product should only be used outdoors in a well-ventilated area.

The product is intended for cutting long grass, weeds, brush and similar vegetation 
at or about ground level. The cutting plane should be approximately parallel to the 
ground surface. The product should not be used to cut or trim hedges, bushes or other 
vegetation where the cutting plane is not parallel to the ground surface.

For safe operation, read and understand all instructions before using the trimmer /
brushcutter. Follow all safety instructions. Failure to follow all safety instructions listed 
below can result in serious personal injury.

 

Do not allow children or untrained individuals to use this unit.

 

Never start or run the engine in a closed or poorly ventilated area; breathing 
exhaust fumes can kill.

 

Clear the work area before each use. Remove all objects such as rocks, broken 
glass, nails, wire or string which can be thrown or become entangled in the string 
head or blade.

 

Wear full eye and hearing protection while operating this unit.

 

Wear heavy long trousers, boots and gloves. Do not wear loose fitting clothing, 
short trousers, jewellery of any kind or use with bare feet.

 

Secure long hair so it is above shoulder level to prevent entanglement in any 
moving parts.

 

Keep all bystanders, children and pets at least 15 m away.

 

Do not operate this unit when you are tired, ill or under the influence of alcohol, 
drugs or medication.

 

Do not operate in poor lighting.

 

Keep firm footing and balance. Do not overreach. Overreaching can result in loss 
of balance or exposure to hot surfaces.

 

Keep all parts of your body away from any moving part.

 

Do not touch area around the exhaust, silencer or engine of the trimmer / brushcutter, 
these parts get hot during operation.

 

Always stop the engine and remove the spark plug wire before making any 
adjustments or repairs except for carburetor adjustments.

 

Inspect the unit before each use for loose fasteners, fuel leaks, etc. Replace any 
damaged parts before use.

JCB-BC26_960443002-01_Manual_final.indd   A2

JCB-BC26_960443002-01_Manual_final.indd   A2

12/2/2010   5:37:58 PM

12/2/2010   5:37:58 PM

Summary of Contents for JCB-BC26

























Reviews: