background image

When connected properly, the top LED on the front of the active speaker
should be green. When first plugged in, it will sometimes take several seconds
for the Control 2.4G active speaker to initialize and “wake up.” Until then, the
top LED will be in red. Once the top LED is green, the bottom LED should flash
green until the transmitter and active speaker “lock in.” It will then also illumi-
nate in solid green. This LED will illuminate in orange if the local input on the
active speaker is selected (see Page 8 under Local Input for more details).

Connection Option B

Connecting using the 1/8-inch single-pin stereo jack on your source:

NOTE: 

Make sure power is turned off on all components.

Step 1.

Connect the RCA – 1/8-inch mini-jack cable (included) to the preamp out, line
out or headphone output of your portable audio player and the inputs on the 
transmitter module 

D

, as shown in Figure 5.

Step 2.

Place the active speaker in the desired location in your home near an AC 
outlet, as it needs to plug into the wall.

Step 3.

Connect the speaker wire (included) to the push terminals on the active 
speaker 

5

and the push terminals on the rear of the passive speaker 

9

as shown in Figure 3. Please note that the speaker wire supplied features a
polarity stripe to help distinguish its two conductors. Use this polarity stripe 
to ensure that you are connecting the positive (+) terminal on one speaker to
the positive (+) terminal on the other, and the negative (–) to the negative (–). 
It does not matter whether you use the striped conductor for connecting the
positive (+) terminals or the negative (–) terminals.

Step 4.

Plug the transmitter module 

B

and active speaker 

6

into the wall outlet,

using the correct power supply and power cord. Make sure the transmitter’s
antenna 

A

is extended upward.

Make sure the ID code setting on the transmitter 

C

is set to the same setting as

that on the active speaker 

4

. See Page 8 of this manual for more information 

on ID codes. When connected properly, the top LED on the front of the active
speaker should be green. When first plugged in, it will sometimes take several
seconds for the Control 2.4G active speaker to initialize and “wake up.” Until
then the top LED will be in red. Once the top LED is green, the bottom LED should
flash green until the transmitter and active speaker “lock in.” It will then also
illuminate in solid green. This LED will illuminate in orange if the local input on
the active speaker is selected (see Page 8 under Local Input for more details).

Figure 5.

 INPUT 

RL

ID

CODE

1234

Po

r

table Audio Devi

c

e o

r

C

ompute

r

 Headphone Ja

c

k (1/8") Mini

On-Air OM.qxd  11/14/06  10:19 AM  Page 7

 
 

  On Air™ Control 2.4G

 

 

 

 

 

 

 

 

 

 

   

 

 

 

6

Summary of Contents for On Air Control 2.4G














Reviews: