background image

Before carrying out maintenance, always extract the cartridge from the tool and disconnect the charging 
stand from the mains. Allow the equipment to cool down.

- Use a damp cloth to clean the casing and the tool. Alcohol can only be used to clean the metal parts.

- Periodically check that the metal parts of the tool and tool holder are clean so that the charging 

works properly.

- Maintain the tip surface clean and tinned prior to storage in order to avoid tip oxidation. Rusty and 

dirty surfaces reduce heat transfer to the solder joint.

- Do not use liquids such as alcohol, thinner or benzene to clean the tablet. 

- Repairs should only be performed by a JBC authorized technical service.

Maintenance

Safety

- Do not use the units for any purpose other than soldering or rework. Incorrect use may cause a fire.

- The power cord must be plugged into approved bases. When unplugging it, hold the plug, not the wire.

- Do not attempt to dismantle or open the housing of the tool as it may cause damage.

- Do not work on electrically live parts.

- The tool should be placed in the stand when not in use in order to charge the batteries. 

- The soldering tip or nozzle, the metal part of the tool and the stand may still be hot even when the 

station is turned off. 

- Do not leave the tool unattended when it is on.

- Avoid flux coming into contact with skin or eyes to prevent irritation.

- Be careful with the fumes produced when soldering.

- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working 

to avoid personal harm.

- Utmost care must be taken with liquid tin waste, which can cause burns.

- This appliance can be used by children over the age of eight and also persons with reduced physical, 

sensory or mental capabilities or lack of experience provided that they have been given adequate 
supervision or instruction concerning the use of the appliance and understand the hazards involved. 
Children must not play with the appliance.

- Maintenance must not be carried out by children unless supervised.

- Do not expose the tablet to high temperatures, humidity or dust. Avoid direct sunlight. 

- Do not drop the portable display or the tool, as it may cause damage or malfunction.

- Do not disconnect your device when it is in fi le transfer mode.

- Do not use the portable display in places where wireless communications are restricted.

  It is imperative to follow safety guidelines to prevent electric shock, injury, fire
  or explosion. 

24

Clean the contact 

surfaces regularly to 

ensure that the tool 

gets charged correctly

Summary of Contents for B-IRON 500





























Reviews: