background image

1

2

5

Retention

Clamps

Cartridge Exchanger

Cartridges are held in place inside the cartridge 
exchanger thanks to the retention clamps (5), 
with the advantage that the cartridges do not 
fall into the exchanger and the cartridge tips are 
therefore protected.

The cartridge exchanger of B·IRON stations 
works with C210 and C115 cartridges.

Cartridge Retention

The cartridge exchanger saves time and allows to change cartridges safely without switching the 
tool off.

Place the cartridge over one of the slots of the 
cartridge exchanger and press down (1) until 
you hear a click. Then pull the handle out (2) 
to remove the cartridge.

1. Removing Cartridges

Cartridge 

Exchanger

C115 

Cartridge

Place the handle over a cartridge and press the 
handle down to insert the cartridge.

2. Inserting Cartridges

C115 Cartridge Retention Area

The holding area of C115 cartridges is delimited 
by the two rings at the cartridge shaft (x).

C210 Cartridge Retention Area

The holding area of C210 cartridges goes from 
the collar of the tip until the cartridge begins 
to widen (x).

C210 

Cartridge

x

x

1

2

5

Retention

Clamps

Cartridge Exchanger

Cartridges are held in place inside the cartridge 
exchanger thanks to the retention clamps (5), 
with the advantage that the cartridges do not 
fall into the exchanger and the cartridge tips are 
therefore protected.

The cartridge exchanger of B·IRON stations 
works with C210 and C115 cartridges.

Cartridge Retention

The cartridge exchanger saves time and allows to change cartridges safely without switching the 
tool off.

Place the cartridge over one of the slots of the 
cartridge exchanger and press down (1) until 
you hear a click. Then pull the handle out (2) 
to remove the cartridge.

1. Removing Cartridges

Cartridge 

Exchanger

C115 

Cartridge

Place the handle over a cartridge and press the 
handle down to insert the cartridge.

2. Inserting Cartridges

C115 Cartridge Retention Area

The holding area of C115 cartridges is delimited 
by the two rings at the cartridge shaft (x).

C210 Cartridge Retention Area

The holding area of C210 cartridges goes from 
the collar of the tip until the cartridge begins 
to widen (x).

C210 

Cartridge

x

x

Reference Mark

Reference Mark

*Inserting C210 Cartridges

Push the cartridges inside the handle until the 
the reference mark is aligned with the edge 
of the handle.

Reference Ring

Reference Ring

*Inserting C115 Cartridges

Push the cartridges inside the handle until the 
reference ring rests against the sealing plug.

Holes

Depending on the shape of the tip, use the 
holes on the sides of the cartridge exchanger 
to properly adjust the cartridge.

Important: 

Push the cartridge in as far as it 

will go, making sure that it is firmly assembled*.

3. Fixing Cartridges

C210 Cartridge Holder

The cartridge holder (4x slots) is used to 
store cartridges. It allows to have different 
cartridges quickly at hand and it works with 
C210 Cartridges.

Cartridge Holder 

Slots

C115 Cartridge Adapter

Since C115 cartridges have a smaller diameter 
than C210 cartridges, adapters must be used 
to store them in the cartridge holder.
These adapters must simply be inserted from 
above into the slots of the cartridge holder.

Cartridge 

Adapter

Reference Mark

Reference Mark

*Inserting C210 Cartridges

Push the cartridges inside the handle until the 
the reference mark is aligned with the edge 
of the handle.

Reference Ring

Reference Ring

*Inserting C115 Cartridges

Push the cartridges inside the handle until the 
reference ring rests against the sealing plug.

Holes

Depending on the shape of the tip, use the 
holes on the sides of the cartridge exchanger 
to properly adjust the cartridge.

Important: 

Push the cartridge in as far as it 

will go, making sure that it is firmly assembled*.

3. Fixing Cartridges

C210 Cartridge Holder

The cartridge holder (4x slots) is used to 
store cartridges. It allows to have different 
cartridges quickly at hand and it works with 
C210 Cartridges.

Cartridge Holder 

Slots

C115 Cartridge Adapter

Since C115 cartridges have a smaller diameter 
than C210 cartridges, adapters must be used 
to store them in the cartridge holder.
These adapters must simply be inserted from 
above into the slots of the cartridge holder.

Cartridge 

Adapter

12

Summary of Contents for B-IRON 500





























Reviews: