JB Systems SMOOTH SCAN-3, Operation Manual

Page: 6 / 40

ENGLISH USER MANUAL
JB SYSTEMS ® 7/75 SMOOTH SCAN-3 LASER
4) IR remote MODE:
The laser can be controlled by the IR remote control:

Press the FUNC-button until the display shows: “REM”.

Press the ENTER-button to confirm your choice.
Note: In any standalone mode (excepted REM and SLA), press ON/OFF for 2 second to activate remote
function.
AUTO SHOW
MUSIC SHOW
LASER ON/OFF
COLOR
EFFECT PAUSE
CHANGING PATTERN
SOUND SENSIVITY
FIXED PATTERN (FROM 1 TO 48)
PATTERN REPEATING
Remote control details:
Button function Description
ON/OFF
In REM mode: turn on/off the laser.
In any other standalone mode except SLAVE: press 2s to
turn on the REM mode
AUTO Auto running show
MUSIC
Sound activated show, the blue is flashing when the
sound is detected.
Sound sensivity
In sound activated mode, press music+B+1to9 to change
the sensitivity settings
COLOR
CHANGING
To change the color from red to green or red & green
PATTERN
CHANGING
To show and change patterns
FIXED
PATTERN
You can select one pattern from 1 to 48
PATTERN
REPEAT
Last pattern and current pattern cycle repeating
5) DMX512 MODE:
The laser can be controlled by any standard DMX-controller in 2 different DMX-modes:

1 CHANNEL MODE: for extremely easy setup and use! (display shows “1Ch”)

17 CHANNEL MODE: for full control of all possibilities. (display shows “17c”)

Connect the DMX input of the laser to the DMX output of the previous unit in the chain or directly to the
DMX-output of your controller.
 Press the FUNC-button until the display shows: “1C” or “17C”.
ENGLISH USER MANUAL
JB SYSTEMS ® 8/75 SMOOTH SCAN-3 LASER

Press the UP/DOWN buttons to select the DMX-mode. (1Ch or 17ch)

Press the ENTER-button to confirm your choice.

Press the FUNC-button: the 3 digit number on the display starts blinking.

Select the DMX-address
 Press the ENTER-button to confirm your choice.
Note: the display blinks when the unit is in DMX-mode and no DMX-signal is detected.
Some more information on DMX512:
The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You need to
“daisy chain” your DMX controller and all the connected light effects with a good
quality XLR M/F balanced cable. To prevent strange behavior of the light effects,
due to interferences, you must use a 90
Ω to 120 Ω terminator at the end of the chain.
Never use Y-splitter cables, this simply won’t work!
Each effect in the chain needs to have its proper starting address so it knows which
commands from the controller it has to decode.
1 CHANNEL DMX-CONFIGURATION OF THE LASER:
position
DMX-
value
function remarks
8 240-255 SOU
Sound activated show with RGY
colors
7 210-239 So2
Sound activated show with GREEN
color
6 180-209 So1 Sound activated show with RED color
5 150-179 Aut Automatic show with RGY colors
4 120-149 Au2 Automatic show with GREEN color
3 090-119 Au1 Automatic show with RED color
2 060-089 SOP Sound activated pattern effect show
1 030-059 AUP Auto running pattern effect show
0 000-029 STANDBY Laser output off
17 CHANNEL DMX-CONFIGURATION OF THE LASER:
IMPORTANT REMARK: DMX Channel1 is used to set the different working modes of the laser.

To use the laser in full 17 channel mode, channel 1 must be set to value 221 or higher.

Depending on the DMX-values of channel1, different mode can be applied:
Channel
DMX-
value
function
CH1
Mode
000-020 Laser OFF
021-040 AUT
041-060 AU1
061-080 AU2
081-100 AU3
101-120 SOU
121-140 SO1
141–160 SO2
161-180 SO3