ENGLISH
OPERATION MANUAL
JB SYSTEMS®
7/68
iMove 5S
Tilt Inversion
Normal: Tilt movement is not inversed.
Tilt inversion: tilt movement is inversed
Press the MENU button until
is shown on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP buttons to select
(normal) or
(tilt inversion) mode.
Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Led Display
Display on: display is always on.
Display off: display is off when not used.
Press the MENU button until the display shows
.
Press the ENTER button, the display starts blinking.
Use DOWN and UP buttons to select
(display always on) or
(display off when not used).
Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Display Inversion
Display normal: display is readable when the unit is on the floor.
Display inversion: display is readable when the unit is mounted upside down.
Press the MENU button untill
is blinking on the display. (normal display)
Use the ENTER button to change to the mode
(display inversion), the option will be automatically
stored after 8 seconds. Or press the ENTER button again return to the mode
(normal display).
To go back to the functions press the MENU button.
Focus Adjust
Used to help you adjusting the focus of the light beam and gobos.
Press the MENU button untill
is blinking on the display.
Press the ENTER button so the unit goes to the “tilt 90°” position.
Press the ENTER button so the unit goes to the “pan 0°” position.
Press the ENTER button so the unit goes to the “pan 90°” position.
Press the ENTER button so the unit goes to the “pan 180°” position.
Press the ENTER button so the unit goes to the “pan 270°” position.
In the Previous 5 steps you are able to adjust the focus with the UP/DOWN buttons on the unit (the display
shows the current focus status).
Attention:
please note that you can only set an “average focus” for all 5 positions, so it is not possible to set
the focus perfectly sharp for all directions.
To go back to the functions press the MENU button.
Self-Test
Used to activate the internal “self-test” program which shows all possibilities of the unit.
Press the MENU button untill
is blinking on the display.
Press the ENTER button to start the internal self-test program.
To go back to the functions press the MENU button.
ENGLISH
OPERATION MANUAL
JB SYSTEMS®
8/68
iMove 5S
Fixture Hours
Used to show the number of working hours of the unit.
Press the MENU button untill
is blinking on the display.
Press the ENTER button to show the number of working hours in the display.
To go back to the functions press the MENU button.
Reset
Used to force a reset of the unit.
Press the MENU button untill
is blinking on the display.
Press the ENTER to reset all channels to their standard position.
To go back to the functions press the MENU button.
Please also check the chapter about the DMX-channel configuration of the unit to find out how you can force
a reset by DMX.
HOW TO CONNECT THE UNIT BY DMX
The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You
need to “daisy chain” your DMX controller and all the connected light effects with a good quality
XLR M/F balanced cable (ex. JB Systems ref. 7-0063). To prevent strange behavior of the light
effects, due to interferences, you must use a 90
Ω
to 120
Ω
terminator at the end of the chain.
Never use Y-splitter cables, this simply won’t work!
Each light effect in the chain needs to have its proper starting address so it knows which commands from the
controller it has to decode.
HOW TO SET THE THE RIGHT STARTING ADDRESS:
Refer to the previous chapter (DMX-512 address setting) to learn how to set the starting address on this unit.
The starting address of each unit is very important. Unfortunately it is impossible to tell you in this user
manual which starting addresses you have to set because this completely depends on the controller you will
use… So please refer to the user manual of your DMX-controller to find out which starting addresses you
must set.
