Jaytech 1200 V4 Installation & User Manual Download

Page: 19 / 21

- 17 -

Fault

appearance

Fault cause

Solutions

Opener without any

action

1. Power supply

2. Plug wire is loose

1. Check the power supply to openers.

2. Carefully open the motor cover, check all plug wire on control boards.

Opener doesn

’t work,

LED displays

“-”

Faulty learning of

“UP” or “DOWN”

travel limit

Learn

“UP” and “DOWN” travel limit again follow the manual

The door can only open,

can not close

In operation with photo beam.

Or photo beam function is available but

with no photo beam connected.

Check photo beam, move away the obstruction.

Cancel the photo beam function if there

’s no photo beam connected. (follow the

instruction manual)

Open and close action is

reversed

Reversed connection of the positive

and negative of motor wire to the

control board.

＊

Power off firstly, open the motor cover and reverse the positive and negative of

motor wire on the control board. Re-set the travel limit.

Door auto reverse to full

open before closing

completely

In operation with safety reverse

function. Obstruction or door

maintenance required

1. Check the door springs and for any obstructions

2. Re-set the travel limit.

3. Increase the force value of safety reverse.

Transmitter doesn

’t work

1. Flat battery

2. Antenna is loose or not well

extended

3. Interference around nearby

1. Replace new battery

2. Extend the antenna on the opener

3. Eliminate signal interference ( door bells, baby monitor, alarm etc)

Can not match new

transmitters

1. Memory is full

2. New transmitters are not compatible

with opener

Press and hold on

“CODE” button for more than 8 seconds until the LED flashes

“C”, delete all stored codes, then match new transmitters again.

2. Choose our transmitters only.

LED displays

“

”, opener

does not work

1. Motor plug wire is loose

2. Control board is damaged

1. Re-insert motor plug wire

＊

2. Replace new control board

LED displays

“

”, opener

does not work

1. Motor is damaged

＊

1. Replace new motor

LED displays

“

” after

opener operates several

centimeters only

1. Hall element wire plug loose

between hall element and control

board.

2. Hall element or control board is

damaged

1. Check the wire plug

＊

2. Check the hall element

＊

3. Replace control board

Note: Only the qualified professional person can carry out the maintenance marked with

“

＊”

Summary of Contents for 1200 V4






















Search results

Summary of Contents for 1200 V4

Reviews:

Related manuals for 1200 V4

Brands by name

Popular brands

Jaytech 1200 V4, Installation & User Manual

Search results

Summary of Contents for 1200 V4

Reviews:

Related manuals for 1200 V4

Brands by name

Popular brands