Javad HPT401BT User Manual Download Page 29

Page: 29 / 36

Appendix A

www.javad.com

PECIFICATIONS

1. Technical Specifications

1.1. General Radio Specifications

Table 1. General Radio Specifications

Parameter

Details

Operating Frequency Range

406 - 470 MHz (EU)
406.1 - 470 MHz (USA)
406.1 - 430; 450 - 470 MHz (Canada)

Channel Spacing

25/12.5/6.25 kHz (USA for 406-420 MHz)
12.5/6.25 kHz (USA for 421-470 MHz)
25/12.5/6.25 kHz (Canada)
25/20/12.5 kHz (EU)

Data Rate
(25/20/12.5/6.25 kHz
Channel Spacing)

9600/7500/4800/2400 bps – DBPSK/GMSK
19200/15000/9600/4800 bps – DQPSK/4FSK
28800/22500/14400/7200 bps – D8PSK
38400/30000/19200/9600 bps – D16QAM

Roaming Speed for DBPSK modulation

75 mph / 120 km/h

Modulation

GMSK/4FSK/DBPSK/DQPSK/D8PSK/D16QAM

Nominal Impedance

50 Ohms

End to End delay

60 ms

Communication Mode

Time Division Duplex (TDD)
Time Division Multiple Access (TDMA)

Maximum Distance Range

8 miles / 12.87 km

Serial port

Serial (RS-232) up to 115200 bps.
Serial port configurable as RS-232 or
RS-422, or RS-485

USB

USB 2.0 device port

Bluetooth

Bluetooth V2.0 Class 2 supporting SPP Slave and
Master Profiles

Bluetooth Antenna

Embedded

Battery

One embedded, 7.2V, 5850 mAh

Operation Time (battery-powered)

6 hours (typ.)

Summary of Contents for HPT401BT




































Search results

Summary of Contents for HPT401BT

Reviews:

Related manuals for HPT401BT

Brands by name

Popular brands

Javad HPT401BT, User Manual

Search results

Summary of Contents for HPT401BT

Reviews:

Related manuals for HPT401BT

Brands by name

Popular brands