Janus AudioControl Director M4800 User Manual Download Page 7

Page: 7 / 16

AudioControl M6400/M4800/D4600

Control4 Driver User Guide

Janus Technology Ltd

The following properties are available, some of which are user editable:

Setting

Description

Driver Version

Reports the release version of the driver

Model

The device model being used

Port

Specify the port number used to communicate with the
amplifier (default 23)

Operational Status

Reports the current connection status

Control4 Zone X controls
AudioControl Y

Control 4 zones can be mapped to either AudioControl zones, or
to AudioControl groups. See an explanation below.

Debug Mode

For support use only

Debug Subsystems

For support use only

Debug Level

For support use only

Table 1: Driver Properties

Summary of Contents for AudioControl Director M4800

















Search results

Summary of Contents for AudioControl Director M4800

Reviews:

Related manuals for AudioControl Director M4800

Brands by name

Popular brands

Janus AudioControl Director M4800, User Manual

Search results

Summary of Contents for AudioControl Director M4800

Reviews:

Related manuals for AudioControl Director M4800

Brands by name

Popular brands