Janus AudioControl Director M4800 User Manual Download Page 15 | Manualshive

Page: 15 / 16

background image

AudioControl M6400/M4800/D4600

Control4 Driver User Guide

Janus Technology Ltd

Copyright © 2018

14

Driver Commands

The driver features a number of commands used for control. Choose the Programming
pane and select the driver in the Device Actions window:

Figure 11: Driver Commands

The driver contains the usual commands found in amplifier drivers, including discrete input
selection as well as the ability to raise, lower, and set volume. Additionally exposed are
some Device Specific Commands; these can be seen in the drop down box in Figure 5.

Command

Description

Set Main Power

Turns the main power on or off

Mute All Zones

Mutes or unmutes all zones

Signal sense

Turns signal sense on or off

Recall EQ

Recalls an equalizer preset for a specific C4 zone (note, not for
an AudioControl zone)

«
...
13
14
15
16
»

Summary of Contents for AudioControl Director M4800

















Reviews:

No comments

Related manuals for AudioControl Director M4800

Renaissance Signature Mk II

Brand: VAC Pages: 12

9440A POWER AMPLIFIER

Brand: Altec Lansing Pages: 4

Brand: Crown Pages: 72

Brand: Thinuna Pages: 12

Brand: Fenton Pages: 7

Brand: dB Pages: 6

Brand: Electro-Voice Pages: 4

Brand: Movon Pages: 44

Brand: Laboga Pages: 24

Brand: R.V.R. Elettronica Pages: 79

Brand: DC Pages: 8

Brand: McIntosh Pages: 36

Brand: Sansui Pages: 14

Tube Ultragain T1953

Brand: Behringer Pages: 23

Brand: Toa Pages: 16

Brand: Advance acoustic Pages: 20

Brand: Kustom Pages: 8

Brand: Merlaud Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands