background image

LTE910XF v6.00 CAT 1 Hardware User Guide JA20-UM-LTE-C1_v6     Page 7    Rev: 02    Date: 09/07/18

© Copyright 2018 Janus Remote Communications   

Specifications subject to change without notice

   All Rights Reserved   See website for latest revision.    Not intended for life support applications.

3. IMPORTANT DESIGN CONSIDERATIONS continued

3.4 Network Connection Status LED

The ON/nSLEEP signal on pin 13 drives the on-board LED indicating network status. By default, the LTE module has this setting disabled. 

Use the following commands to enable and save this feature. 

First, configure the GPIO for alternate function:  

 

 

AT#GPIO = 1,0,2

The modem should respond with:  

 

 

OK

Next, set the desired LED behavior with this command:
   

AT#SLED=2,10,10

The modem should respond with:
   

OK

Finally, commit the changes to non-volatile memory so the setting will persist across power down/power up:
   

AT#SLEDSAV

The modem should respond with:
   

OK

LED Status  

Network Status Indication

Permanently OFF  

Device OFF or setting disabled (see above)

Permanently ON  

Searching for Network & Not Registered

Slow Blinking  

Registered with full service

Permanently ON  

Call is active (Modem has been registered)

3.5 FOTA

See Janus Application Note 117 – FOTA (Firmware Over The Air)

The certification of the following devices for use on the Verizon Wireless network REQUIRES that the end user 
implement an automated FOTA procedure on their devices that would allow the cellular module firmware to be up-
dated if required:

   

 

 

 

LTE910CF  V3.0  

 

LTE910XF  V6.0

   

 

 

 

LTE910CF  V6.0  

 

LTE910XF  V8.0

   

 

 

 

LTE910CF  V11.0 

 

LTE910XF  V11.0

Failure to implement an automated FOTA procedure violates the certification requirements of the cellular modem 
and may result in units becoming unusable on the cellular network in the future. Your end device must support the 
firmware over the air update for the cellular modem
You may use your own FOTA system to update the cellular modem firmware over the air. You may also be able to 
use the Verizon Wireless FOTA system, and FOTA services may be available from other 3rd party vendors.

To inquire about Verizon Wireless FOTA system information and technical specifications,  

contact [email protected] 

Summary of Contents for LTE910XF v6.00













Reviews: