Janome MS5027PR Page 37 Service Manual Download

Page: 37 / 41

MS5027PR

MECHANICAL ADJUSTMENT

REPLACEMENT AND ADJUSTMENT OF NEEDLE THREADER PLATE

* IF THE NEEDLE THREADER IS DAMAGED, REPLACE IT OR ADJUST AS FOLLOWS TO REPLACE

THE NEEDLE THREADER COVER:

PULL OUT THE THREADER COVER (DRAWING. 1).

TO ATTACH THE THREADER COVER, MATCH THE GROOVE TO THE PIN (B) AND INSERT THE

THREADER COVER (C).

ADJUSTMENT OF THREADER PLATE:

IF THE HOOK (D) IS TOUCHING THE RIGHT OR LEFT SIDE OF NEEDLE EYE, LOOSEN

THE SETSCREW (E) AND SLIDE THE THREADER PLATE (H). (SEE DRAWING 2)

IF THE HOOK (D) IS TOUCHING THE TOP OR BOTTOM SIDE OF NEEDLE EYE, REMOVE THE FACE

COVER AND LOOSEN THE SETSCREW (F) AND ADJUST THE THREADER POSITION SET PLATE (G).

HOOK (D)

THREADER KNOB

DRAWING 1

PIN (B)

THREADER POSITION SET PLATE (G)

SETSCREW

VIEW X

THREADER PLATE (H)

SETSCREW (E)

HOOK (D)

DRAWING 2

Summary of Contents for MS5027PR










































Search results

Summary of Contents for MS5027PR

Reviews:

Related manuals for MS5027PR

Brands by name

Popular brands

Janome MS5027PR, Service Manual

Search results

Summary of Contents for MS5027PR

Reviews:

Related manuals for MS5027PR

Brands by name

Popular brands