Janome Memory Craft 3000 Page 16 Service Manual Download | Manualshive

Page: 16 / 31

background image

To adjust the stretch feed balance

When the triple straight stitch is sewn with the feed balancing dial (C) at the standard setting
mark (G, the forward feed (A) and reverse feed (B) should be same length.

1. Set the triple straight stitch and the feed balancing dial at standard setting mark (G).
2. Remove the screws (D) and base cap (E).
3. Adjust the stretch stitch feed balance by turning the adjusting screw (F) in direction A or B.
4. Attach the base cap (E) with screws (D).

14

«
...
14
15
16
17
18
...
»

Summary of Contents for Memory Craft 3000
































Reviews:

No comments

Related manuals for Memory Craft 3000

Brand: Janome Pages: 43

Brand: Tornado Pages: 14

Brand: GBC Pages: 74

MEMORYCRAFT 300E

Brand: Janome Pages: 48

Brand: Singer Pages: 68

Brand: Magnum Pages: 32

Brand: Baby Lock Pages: 112

Brand: XIMEA Pages: 19

Brand: GBC Pages: 18

Brand: Spektrum Pages: 44

Brand: JUKI Pages: 62

Brand: Canon Pages: 2

Brand: JUKI Pages: 136

Brand: SSS Siedle Pages: 16

Brand: IPC Gansow Pages: 2

Brand: Duerkopp Adler Pages: 31

Brand: Duerkopp Adler Pages: 55

Brand: Duerkopp Adler Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands