Janome Magnolia 7306 Instruction Book Download Page 2

Page: 2 / 40

IMPORTANT SAFETY

INSTRUCTIONS

This sewing machine is not a toy. Do not allow children to play with this machine.

The machine is not intended for use by children or mentally infirm persons without supervi-

sion.

This sewing machine is designed and manufactured for household use only.

Read all instruction before using this sewing machine.

DANGER

–

To reduce the risk of electric shock:

1. An appliance should never be left unattended when plugged in.

Always unplug this sewing machine from the electric outlet immediately

after using and before cleaning.

2. Always unplug before replacing a sewing machine bulb.

Replace bulb with same type rated 15 watts.

3. Do not reach for the appliance that has fallen into water.

Unplug immediately.

4. Do not place or store appliance where it can fall or be pulled into a tub or

sink. Do not place in or drop into water or other liquid.

Summary of Contents for Magnolia 7306









































Search results

Summary of Contents for Magnolia 7306

Reviews:

Related manuals for Magnolia 7306

Brands by name

Popular brands

Janome Magnolia 7306, Instruction Book

Search results

Summary of Contents for Magnolia 7306

Reviews:

Related manuals for Magnolia 7306

Brands by name

Popular brands