manualshive.com logo in svg

Janome AirThread 2000D, Service Manual

Share
Download
Janome AirThread 2000D Service Manual Download Page 9

7

Hook of looper cover position detecting arm

MODEL: AirThread 2000D

Replacing External Parts

Looper cover

Looper cover

To remove:
1.  Remove the base plate.
2.  Remove the setscrews (2 pcs.).
3.  Release the hook of looper cover position detecting 

arm from the looper cover shaft.

4.  Remove the looper cover.

Setscrew

Hook of looper cover  
position detecting arm

Looper 
cover shaft

Setscrew

To attach:
1.  Set the looper threader switch lever to the  
 

"THREADING" (right side). 

 

Make sure that the looper cover position detecting  

 

arm comes in front of the looper. threader switch  

 

lever connecting lever (shown as the looper cover  

 

position detecting arm on top the looper threader  

 

switch lever connecting lever in the figure).

2.  Put the hook of looper cover position detecting arm on 

the looper cover shaft.

3.  Tighten the setscrews (2 pcs).
4.  Attach the base plate.

Looper cover 
position detecting arm

Looper cover shaft

Looper threader switch lever 
connecting lever

Summary of Contents for AirThread 2000D














































Reviews:

No comments

Brands by name

Popular brands

Load more brands