manualshive.com logo in svg

Janome AirThread 2000D, Service Manual

Share
Download
Janome AirThread 2000D Service Manual Download Page 33

31

0

1

2

Mechanical Adjustment

MODEL: AirThread 2000D

To adjust the thread tensions

Use a standard thread #50. Do not pass the thread through the top cover thread guide.
Standard tension:
Left needle:  Tension dial set to 3, 30-40 gf, Tension dial set to 9, 80 gf or more
Right needle:  Tension dial set to 3, 15-19 gf, Tension dial set to 9, 50 gf or more
Upper looper: Tension dial set to 3, 9-13 gf, Tension dial set to 9, 30 gf or more
Lower looper: Tension dial set to 3, 18-22 gf, Tension dial set to 9, 55 gf or more

To adjust:
1.  Use a standard thread to check the tension.
2.  If the thread tension is not correct, turn the tension 

dial so that the thread tension becomes the value 
represented by “3” of the dial (ignore the real number 
on the dial). 

3.  Remove the top cover.
4.  Raise and hold the adjusting plate with a screwdriver. 

Turn the dial to match the position of “3” with the notch 
(position of the setting mark on the top cover).

5.  Check the thread tension again. Repeat the procedure 

of steps 2 and 4 until the thread tension becomes 
correct.

6.  Attach the top cover.

Thread tension dial

Notch of 
the thread 
tension plate

Thread

Adjusting 
plate

To pull the thread to this direction

Holding the adjusting plate 
raised with a screwdriver,
turn the dial.

Turn the dial to the 
direction (A) 
to loosen 
the tension

Turn the dial to the 
direction (B) 
to tighten

Thread tension 
plate

Notch of 
the thread 
tension plate

Summary of Contents for AirThread 2000D














































Reviews:

No comments

Brands by name

Popular brands

Load more brands