manualshive.com logo in svg

Jandy AquaPure, Installation And Operation Manual

Share
Download
Jandy AquaPure Installation And Operation Manual Download Page 22

Page 22

Figure 11.  Cell Installation and Flow/Temp/Salinity Sensor

*  Ensure the DC Plug is properly and securely 

   connected to the terminal studs of the cell.

DC Cord Plug is Connected

to Terminal Studs*

O-Ring

Seal

Flow/Temp/Salinity Sensor

O-ring and Union Nut

2 x 2½” or 50mm Tailpiece

with Coupling Nut

2” x 2½” or

50mm Union

or

Sometimes

Not Covered

Temperature

Sensors

Flow/Temp/Salinity Sensor Face must 

be clean at all times for proper operation

Salinity

Studs

5.  Connect the DC cord to the control center. Feed the DC cord through the same strain relief fitting as the 

flow/temp/salinity sensor. Plug the DC cord as shown in Figure 2a, 2b, and 2c.

  CAUTION

Do not bury the electrolytic cell DC cord or Sensor cable directly in the ground. Direct burial can cause 

damage to an electrical cord/cable.

6.  Tighten strain relief fitting screws for the flow/temp/salinity sensor cable and the DC cord. Do not pull 

flow/temp/salinity sensor cable or DC Cord too tight. Allow a little cable slack inside of control center 

enclosure.

7.  Check the wiring prior to reattaching front cover. Be sure the flow/temp/salinity sensor is plugged in. 

The DC cord should be plugged in. Also, check the AC wiring.

  CAUTION

Do not over tighten the strain relief fitting. Over tightening can cause damage to the flow/temp/salinity 

sensor cable.

8.  If disconnected, plug the ribbon cable into the J1 connectors the user interface and the Power Interface 

PCB (See Figures 2a, 2b, 2c, and 10).

  CAUTION

Do not operate the electrolytic cell without water circulation. A buildup of flammable gases can result in 

FIRE or EXPLOSION.

Summary of Contents for AquaPure





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands