manualshive.com logo in svg

Jandy AquaPure, Installation And Operation Manual

Share
Download
Jandy AquaPure Installation And Operation Manual Download Page 13

Page 13

  WARNING

When using electrical products, basic precautions should always be followed, including the following:

•  RISK OF ELECTRIC SHOCK WHICH CAN RESULT IN SERIOUS INJURY OR DEATH. Before 

attempting installation or service, ensure that all power to the device is disconnected/turned off at 

the circuit breaker.

•  Grounding is required. The unit should be installed by a qualified service representative and

 

should be properly grounded. (See 

Section 3.4, Earth Grounding

).

•  Install to permit access for servicing.
•  Read 

Section 1

,

 Important Safety Instructions

. 

Before attempting any electrical wiring, be 

sure to read and follow Safety Instructions. Wiring should only be attempted by a qualified 

professional.

A

Sensor

Sensor

Sensor

Flow

UP

Flow

Flow

A

C

B

(

)

UP

UP

Figure 3. 

Chlorine Generator Cell and Sensor Orientation with Flow Direction

3.2  Plumbing Configurations

3.2.1  Recommended Electrolytic Cell and Sensor Orientation

Shown below are three (3) different cell and sensor orientations. The third port on the cell is designed for 

installation of the sensor and for quick viewing of the cell plates. The minimum flow rate is 30 GPM 

 

(114 LPM).

Summary of Contents for AquaPure





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands