background image

       A Standard Relay's coil is supplied 24 VDC from the Power Center PCB via one of the two driver chips.
When 24 VDC is received by the relay's coil wires,  it closes the contacts that complete the circuit to turn on the
equipment (i.e., power supplied to Line 1 goes out Load 1 to the equipment).
       Standard Relays may be wired to activate a 110 VAC circuit (e.g., Line 1/Load 1) or a 220 VAC circuit
(e.g., Line 1/Load 1 and Line 2/Load 2).

NOTE: If a relay's coil wires are shorted, or an AC relay coil is plugged into a relay socket, when that circuit is
activated, it will damage one of the two relay Driver Chips (Part No. 3814) on the Power Center PCB. (These
chips can be replaced/see Page 4).

                  Specification:
                              Maximum Contact Ratings:
                                       3 hp at 220 VAC
                                       1 1/2 hp at 110 VAC
                                       25 amps - Inductive
                                       1500 watts - Incandescent
                               Relay Coil: 24 VDC
                               Resistance across coil: 0.300K Ohms
                               Amperage draw of coil: 0.10 Amps

Operation:

W iring for a S tandard R elay

R elay C oil (24 VD C )

Transform er 
  120 VA C  Prim ary
  24 VA C  S econdary

F ilte r P um p  R e la y

A ux .  3  R e la y

O p tio n a l

L

oad 2

L

ine 2

L

oad 1

L

ine 1

O p tio n a l

O p tio n a l

O p tio n a l

W ire  N u t to

1 2 0   VA C   P o w er

Low

 vol

tage r

a

cew

a

y (

do not

 r

un 

hi

gh v

o

lt

age 

in

 t

h

is

 com

par

tm

ent

)

B re akers

G ro und

Ne

u

tr

a

l

B lo w e r

(11 0   VA C )

F ilte r  P u m p

(2 2 0   VA C )

12

0 V

A

C

PR

IM

AR

Y

24 V

A

C

S

E

CO

NDAR

Y

R elay

Li

ne 1

Loa

d 1

Li

ne 2

Loa

d

 2

AquaLink

®

 RS Troubleshooting

5

    3        Standard  Relays

Summary of Contents for AquaLink RS





























Reviews: