background image

pg 7

Carefully strip the outer cord jacket to expose six (6) inches of the underlying three 

insulated wires.

5. Tape the three existing light wires to the replacement light cord with electrical 

insulating  tape.  Avoid  wrapping  too  much  tape  around  the  cords.  Otherwise,  the 

thickness will be too great for the cord to be able to be pulled through the conduit 

to the junction box.

6. After removing the junction box cover, disconnect the light fixture wires. Then, pull 

the cord through the conduit until it is visible in the junction box conduit. Remove the 

tape from the cords and separate the wires.

7. Carefully strip the outer cord jacket from the new light cord to expose six (6) inches 

of the underlying three insulated wires.

8. Connect these three (3) wires to their corresponding junction box circuit wires and 

secure the junction box cover in place.

9. Be sure to leave at least four (4) feet of cord at base of the fixture to coil around the 

light to ensure ease of servicing; reference Figure 1.

10. Install the Color Splash LED light fixture into the niche.

11. Using the stainless steel pilot screw provided, install the Color Splash LED light 

fixture assembly into the niche, carefully tightening the pilot screw. (Reference Figure 

1)

12. Make a final check to confirm proper light operation by switching “on” the main 

switch  or  circuit  breaker  and  the  light  switch.  The  light  should  illuminate  when 

power is switched “on”. If the light is not operating, go back to Step 1 to recheck each 

installation step for proper completion.

INSTALLER  NOTICE: 

This  light’s  external  cord  cannot  be  replaced  and  should  be 

handled with care. Any damage to this external cord necessitates replacing the light. 

This special pilot screw secures and electrically grounds the fixture to the mounting 

ring and wet niche. Failure to install the stainless steel pilot screw provided could 

create an electrical shock hazard, resulting in death or serious injury to pool users, 

installers or others.

WARNING! Use only the 

stainless steel screw 

provided with this underwater 

light. 

Summary of Contents for Color Splash













Reviews: