background image

21

The

device

is intended for use in the electromagnetic environment specified below. The customer or the user

of the

device

should assure that it is used in such an environment.

Immunity

test

IEC 60601 test

level

Compliance

level

Electromagnetic environment - guidance

Portable and mobile RF communications equipment
should be used no closer to any part of the device,
including cables, than the recommended separation
distance calculated from the equation applicable to the
frequency of the transmitter.

Conducted RF

IEC 61000-4-6

3 V

rms

150 kHz to 80 MHz

3 V RMS outside the

ISM band, 6 V RMS

in the ISM and

amateur bands

80% AM at 1kHz

Not applicable

Recommended separation distance

d=0.35√p

d=1.2√p

Radiated RF

IEC 61000-4-3

10 V/m

80 MHz to 2.7 GHz

80% AM at 1kHz

10 V/m

80 MHz to 2.7

GHz

80% AM at 1kHz

80MHz to 800MHz

d=1.2√p

800MHzto 2.7GHz

d=2.3√p

Where, P is the maximum output power rating of the

transmitter in watts (W) according to the transmitter

manufacturer and d is the recommended separation

distance.

Field strengths from fixed RF transmitters, as determined
by an electromagnetic site survey, should be less than the
compliance level in each frequency range. Interference

may occur in the vicinity of equipment marked with the
following symbol:

NOTE 1

At 80 MHz and 800 MHz, the higher frequency range applies.

NOTE 2

These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and

reflection from structures, objects and people.

a

Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land

mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically

with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site

survey should be considered. If the measured field strength in the location in which the

device

is used exceeds the applicable

RF compliance level above, the

device

should be observed to verify normal operation. If abnormal performance is observed,

Summary of Contents for W03

























Reviews: