background image

11

Use instant glue to secure the contacting places.

FUSELAGE ASSEMBLY

Make sure the alignment of both side boards on the tail.

Place F3, F17 and F18 on the working table.

Fit the F18 into the slot on F10.

Place  F21,  F22,  F23,  F24,  F25,  F26  and  F27  on  the  working 

table as picture shown.

Rear view of the tail fuselage; make sure it is bilateral symmetry.

Try to fit the head of F17 into the slot on F5 (the front board on 

the fuselage).

Make sure the top edge of F18 can fit into the slot on F17. Use 

instant glue to secure the F18 in place.

Try to fit the F21 and F22 onto the fuselage. Use instant glue to 

secure them in place.

Try to fit the F19 onto the fuselage and drop some instant glue 

to secure it in place.

Try to fit the tail of F17 into the slot on F10.

Try to fit 5 pieces of F3 on the top of the fuselage. Use instant 

glue to secure the F3 in place.

Try to fit the F28 onto the fuselage and drop some instant glue 

to secure it in place.

Press F17, make sure it is flat and use instant glue to secure 

it in place.

Use sanding paper to trim the excess part of F3.

Summary of Contents for Fokker DVII





























Reviews: