Jain Technology XONIC-100P User Manual Download Page 16 | Manualshive

Page: 16 / 37

background image

16

5.4.2 Measure the installation area distance using ruler

If you find good position for installation, please mark installation area using ruler. Please remember
the area must be enough for Mounting Track installation.

센서를 설치할 위치를 선정하고
센서의 설치 거리를 확인하여 이물질이
없도록 사포나 기타도구를
사용하여 깨끗이 정리한다.

Pipe

5.4.3 Peel Off Pipe Coating and Make install position flat and clean

Please peel off pipe coating and Use abrasive to clean the area.

5.4.4 Install Mounting Track

Install mounting track onto the pipe with stainless steel strap. Fix it tightly.

센서고정용트랙

트랙고정용 스트랩

Space

센서의 설치거리

5.4.5 Install Transducers onto Pipe

Apply couplant onto bottom of transducers and locate transducer into mounting track. Make
transducers clamp-on pipe by tighten a clamp screw.

Peel off any coatings, and make this area
clean and flat for transducer mounting.

Easy Mounting Track

Strap Kit

«
...
14
15
16
17
18
...
»

Summary of Contents for XONIC-100P






































Reviews:

No comments

Related manuals for XONIC-100P

Brand: JGR Pages: 12

Brand: jenway Pages: 18

SourceMeter 2400

Brand: Keithley Pages: 594

System SourceMeter 2601B

Brand: Keithley Pages: 864

Brand: Labgear Pages: 8

SourceMeter 2600B Series

Brand: Keithley Pages: 897

Brand: Olympus Pages: 362

Brand: Olympus Pages: 8

Brand: QUNDIS Pages: 20

Brand: R&S Pages: 2

Brand: Underground Magnetics Pages: 48

Brand: lanry Pages: 2

Brand: lanry Pages: 29

Brand: AEMC Pages: 4

Brand: Ecolab Pages: 95

Brand: Velleman Pages: 15

Brand: Konica Minolta Pages: 42

Brand: Kobold Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands