JAI IIT Camera Systems VIS-CAM 350 Installation Manual Download Page 18 | Manualshive

Page: 18 / 44

background image

IIT Camera System Manual

18

Installation

3.2

Installing the Camera

The camera is mounted using the same VIS Mount as VIS-CAM Systems (300/350/400). Please refer to
section 3.2 in the VIS-CAM System Installation manual for camera mount template and mounting

instructions.

3.2.1

Opening the Camera Housing

The rear plate can be removed by loosening the two screws marked “1” below. Once they are loose

they can be turned by fingers. The screws are retained by springs.

When the rear plate is removed the drawer holding the electronics can be pulled out after removing

the two screws marked “3” in figure B.

The lid is held by a drawbar as shown in figure C (inside view) and figure D of the lid taken off. To

take off the lid the two screws marked “2” in figure A are loosened. Start by turning the screws 6-7
turns counterclockwise and then push them gently back in using the screwdriver. Repeat this until

the screws cannot be pushed in any more. The lid can then be taken off.

«
...
16
17
18
19
20
...
»

Summary of Contents for IIT Camera Systems VIS-CAM 350













































Reviews:

No comments

Related manuals for IIT Camera Systems VIS-CAM 350

Brand: Abus Pages: 162

Brand: Abus Pages: 82

Brand: Abus Pages: 88

Brand: Abus Pages: 2

Brand: Abus Pages: 119

Brand: MagicRadar Pages: 98

Brand: Mami Pages: 16

Brand: NA-DE Pages: 8

Brand: Mace Pages: 1

Brand: Mini Gadgets Pages: 6

Brand: VS2 Pages: 2

Brand: StarVedia Pages: 2

VK2-3MPBIR28V12re

Brand: Vista Pages: 14

Brand: Silent Witness Pages: 26

DDF4900HDV Series

Brand: dallmeier Pages: 71

Brand: Vacron Pages: 17

Brand: OpenEye Pages: 44

Brand: Satel Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands