background image

CV-A50 IR

 

 

6.9. Start/Stop Mode 

The exposure time is controlled by the interval between the ext. trigger and the ext. VD signal. 
The exposure starts at the first HD pulse after the falling edge of the ext. trigger, and stops 14.5 
H after the falling edge of the VD pulse. It means that the trigger pulse must be applied after 
the external VD pulse, for exposures less than 14.5 H. The range can be between 1/60 to 
1/10,000 for EIA, and 1/50 to 1/10,000 for CCIR. The Start/Stop mode is a continuous mode 
where the VD signal must be given continuously. It is not possible to input external VD randomly. 

The difference between interlaced frame accumulation or field accumulation can be explained 
as follow. 
Both modes have 2 fields output in an interlaced frame. With frame accumulation, the contents 
in the ODD and EVEN sync fields will come from sensing field 1 and 2 on the CCD sensor. With 
field accumulation both ODD and EVEN sync fields will contain the signal from sensing field 1 and 
2 added together. 
Non-interlaced with field accumulation needs only 1 trigger pulse for each field.

 

 

To use this mode:  
Set function: 

Trigger mode to “Start/Stop”  

TR=5 

 

Accumulation to “Field” or “Frame” 

FR=0, F=1 

 Scanning 

to 

“Interlaced” 

SC=0 

 

 

Polarity and other functions 

Input: 

Ext. VD to pin 7 on 12 pin connector. 

 

Ext HD to pin 6 on 12 pin connector.

 

 

Fig. 25a. Start/stop mode. Interlaced with frame accumulation.

 

 

 

Fig. 25b. Start/stop mode. Interlaced with field accumulation. 

 

ext. H D

ext. V D

ext. Trig

1 3H

co m po site

vide o

Accum

M in . accum .

a ccu m u la tion

sto ps  h e re

 

Fig. 26. Start/Stop timing details.

- 16 -

 

 

Summary of Contents for CV-A50 IR




























Reviews: