CM-200GE/CM-200GE-RA/CB-200GE/CB-200GE-RA
- 63 -
13.2 Specification table
Specifications
CM-200GE//200GE-RA
CB-200GE/200GE-RA
Scanning system
Progressive scan
Frame rate full frame
24.98 frames/sec. Progressive (1236 lines/frame)
Pixel clock
65 MHz
Line frequency
31.25 kHz ( 1H = 32 µs )
(2080 pixel clock/line)
CCD sensor
1/1.8”. Monochrome ICX274AL
1/1.8” Bayer Color ICX274AK
Sensing area
7.13 (h) x 5.37 (v) mm 1/1.8 inch diagonal
Cell size
4.4 (h) x 4.4 (v)
µ
m
Active pixels
1624 (h) x 1236 (v)
Pixels in video output.
Full Scan
2/3 partial Scan
1/2 partial Scan
1/4 partial Scan
1/8 partial Scan
Vertical Binning
Region-of-interest (ROI)
1624 (h) x 1236 (v) 24.98 fps. H = 31.25 kHz
1624(h) x 824 (v) 35.07 fps H= 31.25 kHz
1624 (h) x 616 (v) 43.82 fps. H = 31.25 kHz
1624 (h) x 308 (v) 69.59 fps. H = 31.25 kHz
1624 (h) x 156 (v) 97.96 fps. H = 31.25 kHz
1624 (h) x 627 (v) 44.49 fps. H = 27.9 kHz ( *Note)
User Definable. Memory read-out
*Note: Vertical binning is for CM-200GE/CM-200GE-RA only
Sensitivity on sensor (minimum) 0.03 Lux (Max. gain, Shutter OFF, 50%
video )
0.24 Lux (Max. gain, Shutter OFF,50%
Green, w/IR cut filter)
S/N ratio
More than 50 dB (0dB gain)
Digital Video output.
GigE Vision Compliant
Mono8,Mono10,Mono10_Packed
GigE Vision Compliant
BAYRG8,BAYGB8,BAYRG10,BAYGB10
Iris video output. Analogue
0.7 V p-p , enabled by internal switch
Gain
Manual -3 to +24 dB (1 step=0.0358dB)
Synchronization
Internal X-tal
GPIO Module
Input/output switch
Clock Generator ( One)
Pulse Generators ( Four)
Configurable 14-in / 9-out switch
12-bit counter based on 25MHz clock or Pixel clock
20-bit counter programmable for length, start point, stop point, repeat
Hardware Trigger modes
Edge Pre-Select , Pulse Width Control, RCT, Frame Delay and Sequence
OB area transfer mode
ON / OFF
Event message
SYNC / ASYNC mode ( Trigger mode status when exposure starts )
Exposure start, Exposure end, Trigger IN, Video start, Video end
Electronic Shutter
Preset Shutter speed
Programmable exposure
Exposure Time (Abs)
GPIO plus Pulse Width
OFF(1/25) and 1/60 to 1/10,000 in 9 steps
2L(64µs) to 1251L ( 40.032ms) in 1L steps
µsec – user definable. Same range as PE
max. 2 sec ( Can be set by 100µs unit or Pixel Clock unit)
Control interface
Register based. GigE Vision / GenIcam compliant
Functions controlled via GigE
Vision Interface
Shutter, Gain, Black Level, Trigger mode, Read out mode,
GPIO setup ,ROI ( GenIcam mandatory functions )
GigE Vision Streaming Control
Packet size, Delayed ( Frame ) read-out, inter-packet delay
Jumbo frame can be set at max. 4K(4040) , Default packet size is 1428 Byte.
Indicators on rear panel
Power, Hardware trigger, GigE Link, GigE activity
Operating temperature
-5
°
C to +45
°
C
Humidity
20 – 90% non-condensing
Storage temp/humidity
-25
°
C to +60
°
C/20% to 90% non-condensing
Vibration
10G (20Hz to 200Hz, XYZ)
Shock
70G
