1
CAUTION
ROUGHING-IN DIMENSIONS
Feed FLEXIBLE FAUCET SUPPLIES (4) and SHANKS (5)
through the mounting hole of lavatory, or mounting
surface.
Install SEAL (3) onto bottom of faucet.
From under side of faucet thread POP-UP ROD (1) into
POP-UP LEVER (2). (Figure "A")
Faucet 831/701 with POP-UP drain
Faucet 831/711 less drain
From below, Install "C" WASHER (6), and LOCKNUTS (7)
onto faucet SHANKS (5). Before final tightening, adjust
faucet so that it is centered and covers mounting hole.
Tighten LOCKNUTS (7) using a screwdriver or hex wrench.
1 0 9 6 4 8
1 0 9 6 4 8
INSTALL FAUCET
3
WATER SUPPLY CONNECTIONS
Connect HOT water supply to left side and Cold to right side.
Faucet supplies are 15-3/4" in length. Loop supplies if they
are to long. If additional length is required, installer must
provide adapters and supplies to connect to shut-off valves.
Use adjustable wrench to tighten connections.
Do not over tighten.
COLD
HOT
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE
PURCHASED SEPARATELY.
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
Channel Locks
TOOLS REQUIRED
Tubing Cutter
Regular Screwdriver
Basin Wrench
APPLY SEALANT
OR TEFLON TAPE
2
A FOAM SEAL (1) is installed on underside of FLANGE (2). (Plumbers
Putty may be used in place of FOAM SEAL (1) if desired.)
Apply sealant or Teflon tape to threads of TAILPIECE (10) and
thread into DRAIN BODY (7) making a water tight seal.
Drop FLANGE (2) into LAVATORY DRAIN (3). From below assemble
RUBBER GASKET (4), PLASTIC WASHER (5) and LOCK NUT (6) onto
DRAIN FLANGE (2). Do not tighten fully.
INSTALL POP-UP DRAIN (831/701/...)
FIG. 2a
FIG. 2b
FIG. 2c
FIG. 2c
FIG. 2a
FIG. 2b
1
4
3
2
5
6
7
8
6
9
2
Adjust STOPPER (13) height by repositioning POP-UP ROD (16) in SWIVEL (15)
and tightening SET SCREW (18).
Assemble POP-UP SWIVEL (15) to PIVOT ROD (11) but do not tighten.
Drop POP-UP ROD (16) through other hole in POP-UP SWIVEL (15) and
tighten SET SCREW (17)
Assemble PIVOT ROD (11), and PIVOT NUT (12) as shown. Install CONCAVE
WASHER (19) into PIVOT ROD OPENING (9) if not preinstalled. Hand tighten
PIVOT NUT (12). Drop STOPPER (13) into drain.
(
To vandal proof drain rotate STOPPER (13) so PIVOT ROD (11) goes
through EYE (14) of STOPPER (13)
. Make connection to "P" TRAP.
Inspect inside DRAIN BODY (7) that SEAL (8) is installed. Thread
DRAIN BODY (7) tight against FLANGE (2) to make a water tight seal.
10
9
7
6
12
19
16
15
17
18
2
10
14
13
11
3
4
5
The PIVOT ROD OPENING (9) in DRAIN BODY (7) should face the rear
of the lavatory. Tighten LOCK NUT (6) on FLANGE (2) to make a water
tight connection with channel locks. Do not over tighten.
Turn off hot and cold water
supplies before beginning.
6
7
15-3/4"
9-3/4"
11-3/8"
5-3/4"
8-1/4"
3-5/8"
1-1/2"
2"
1
2
FAUCET
RECESS
VIEW "A"
2-1/8"
1-1/4"
max. 2"
max. 7"
