20
20
NOTE:
if power is provided with a double line (380-415V 2N), be-
fore making the connection you must remove the indicated jump-
ers, located near the power supply terminal block.
X
To ensure the degree of protection against water as required
by standards, a cable clamp has been installed to make connec-
tion the electrical system easier.
X
The installer must connect the phase wire to the correct ter-
minal and the neutral wire to terminal
N
(in the order indicated).
He must also connect the earth wire to the terminal identified
by the symbol , taking care not to damage the components
inside. When installation is complete, the cable clamp and the
cover of the box must be hermetically closed.
IMPORTANT:
for Countries where 220-240V voltage is
supplied by a two-phase system (L+L), the connection
has to be made on terminals L1 and N anyway.
JACUZZI EUROPE S.p.A. denies all responsibility:
If installation is carried out by personnel unqualified and/or unau-
thorised to certify the work carried out.
If current norms and legal provisions regarding the electric systems
of buildings in the country in which installation is carried out are
not complied with.
If the instructions for installation and maintenance contained in
this manual are not followed.
If unsuitable and/or uncertified materials are used for installation.
If the spas are not installed in compliance with the above provi-
sions.
If incorrect operations are performed that reduce the level of protec-
tion of the electrical equipment against water jets, modify the protec-
tion against electrocution due to direct or indirect contact, or produce
abnormal conditions of insulation, current leakage or overheating.
If any components or parts of the appliance are altered in relation
to the original state when supplied, releasing the Manufacturer
from any liability.
If the appliance is repaired by unauthorised personnel or if spare
parts are used other than the original ones supplied by Jacuzzi Eu-
rope S.p.A.
Check of operation
First start-up
X
Remove the thermal cover of the spa.
X
Check that the filter cartridge is present in its container and
that the various components are properly installed
(see the chap-
ter on maintenance of the filter cartridge).
X
Check that the drain valve on the base (and the ball valves, if
installed) are closed
(refer to the pre-installation instructions en-
closed with the product).
NOTE:
the pipe that connects the overflow to the drain must always
be left open (refer to the pre-installation instructions).
X
Check that all the hydromassage intakes are open.
X
Fill the spa so that the highest nozzles (back) are covered.
4-5 cm
Filling will be performed as decided beforehand by the customer
(see pre-installation sheet, “Preparation for installation” chapter).
If you use the hose for garden work, let water run for a while
before filling the spa. This will eliminate stagnant water in the
hose along with any bacteria that may cause irritations.
We recommend you have the water that you intend to
use to fill the spa analyzed, especially for water hard-
ness. Water that is too soft or too hard may damage
some of the components of the tub (see the user man-
ual, chapter, “Water treatment”, paragraph, ”Hard-
ness of water”); whereas impurities in well water may
clog the cartridge filter and create problems with the
pumps and the hydraulic system.
X
Turn on the all-pole circuit breaker located on the power sup-
ply line
(see the chapter on connections and electrical safety)
.
Notes:
- When first turned on, all of the numbers and LEDs on the control
panel will turn on; the codes relative to the software, firmware and
set control model with dip-switch will appear.
When this time has passed, the system will enter stand-by mode.
X
Press the TEST button of the differential switch located up-
stream from the electrical system to which the spa is connected.
If it does not trip, it may be faulty or it may have tripped due to
problems in the electrical system of the building.
Disconnect the spa and do not use it until you have identi-
fied and eliminated the defect.
X
Check the operation of the hydromassage pumps using the
key
(upon pressing the key for the first time, the pump is acti-
vated; it is turned off by pressing the key a second time)
.
Summary of Contents for Flow
Page 2: ...4 2 3 1 1...
Page 57: ...spa 4 8 spa spa...
Page 58: ...58 ON...
