background image

Normal Operation/Whirlpool System

You can enjoy the Santina spa with or without activating the whirlpool.  Either way, bathing in your spa can be pleasurable,

as well as therapeutic.  After a busy, stressful day, you can look forward to soaking in your spa in still water with no
turbulence—only the gentle warmth of the soothing and relaxing water.

For a more invigorating spa experience, you can take advantage of the built-in whirlpool system.  To do this, push the

SYSTEM switch button to select the JETS mode.  Sit or recline in the spa so you are comfortable.  Since all the jets are
directionally adjustable, you can direct a jet toward an area where muscles feel tense or stiff.  The warmth of the water and
the stimulating water flow from the jet will pleasantly increase circulation.

 For the total whirlpool effect and all-over feeling of well being, you can adjust all jets so they point in a clockwise or

counterclockwise direction to circulate the air and water mixture in a circular motion all about the spa.

Filtration

When you are ready to leave the spa, push the SYSTEM

switch button once to turn off the whirlpool.  This puts the
spa in HTR/FLTR mode. Adjust the HEATER  knob to the
temperature at which you wish the water maintained.  In
this way, the water will be filtered when the heater goes on
to maintain the temperature.  Running the filter pump for at
least two hours per day is sufficient.  Another way to be sure
the water will be filtered is to turn the SYSTEM off and set
the built-in timer in the System Control Module to turn the
system on at a certain time to filter the water.  Be sure there
is sufficient water in the spa (filled to the waterline indicator
mark on the skimmer/filter frame) when the timer is set, or
the spa’s motor/pump could be damaged.  (See page 8 for
instructions on setting the timer.)

Silent Air Induction

The intensity of the whirlpool action is determined by

how much air is inducted into the water.  You have control
of this by adjusting the air induction control knobs located
on both control panels.  For maximum air induction, rotate
each control knob fully counterclockwise to the largest
circle.  For fewer air bubbles, decrease the amount of air
induction by rotating the control knobs clockwise.  When
the knobs are turned to the smallest circles, only water is
being circulated. (See page 10).

Water Rainbow

 

The Water Rainbow spout will add the soothing sound of

a waterfall to your bathing pleasure, as well as provide a
beautiful cascade of shimmering water for an exciting
visual effect.

Activate the waterfall feature by first turning on the

JETS, HTR/FILTER, or FILTER function, then rotate down-
ward the flow control lever located on the left side of the
spout.  Use this lever to adjust the amount of water flowing
through the Water Rainbow spout.  The waterfall affect will
be greatest in the JETS mode.  Turning off the flow at the
fully adjustable jets will dramatically increase Water Rain-
bow flow.

CAUTION

 The water circulating through the Water

Rainbow spout is not fresh water and not suitable
for drinking.

11

FULLY ADJUSTABLE

WHIRLPOOL  JETS

Air Blower

The Santina features a built-in air blower and factory

drilled air holes in the seats of the spa to add to your
enjoyment.

The blower sends air to a channel located under the

spa's seats; this air is distributed through the air holes, and
as the pressurized air is released from the holes, tiny
bubbles are formed.  These bubbles travel upward through
the water and expand until they reach the surface and
burst.  The exciting visual effect of the bursting bubbles
contributes to the overall hydromassage experience.

Activate the blower by pushing the ACCESSORY switch.

DIRECTIONALLY ADJUSTABLE
WHIRLPOOL  JETS

OPERATION

Summary of Contents for D550000
























Reviews: