Jacuzzi booster KIT spa-pack, Installation, Use And Maintenance Manual

Page: 14 / 80

14
Info
The spa-pack booster kit includes the filter system (pump + sand
filter) and the Jacuzzi® photometric analyser.
The Jacuzzi® photometric analyser enables the measurement of
Chlorine (free), pH and temperature values in addition to measuring
out the chemical products required to treat the spa water.
The operating principle is simple: a specific quantity of water is
placed in a suitable measurement unit; the chlorine inside, upon
contact with a special reactant, turns the water colour, red, the
brightness of which enables the stabilization of the disinfectant
concentration and subsequently, corrects the value.
The device completes its task during the filtering cycles, which
must always be scheduled in consideration of the frequency of use
of the spa (refer to the relative documentation).
The range of use of the device falls within 0 to 50 °C, with relative
humidity (non-condensed) in the range of 10 to 95 % RH.
The factory stored values comply with the standard
UNI 10637. For countries in which this directive has not
been acknowledged or integrated in the local regula-
tions, refer to the respective legislation.
Set-up
Please refer to the spa documentation for the set-up of
the hydraulic and electrical systems.
ATTENTION! Before preparing the drain system, con-
sult the local authorities about the regulations for the
discharging of chemically-treated water.
The installer must oversee the piping system enabling connection
of the spa-pack.
- The Client is responsible for providing a drain system of ade-
quate size which can be accessed for cleaning, to which the
drain from the filter and the drain from the photometric analyser,
are connected.
- It is necessary to provide an independent power supply line
(not originating from the main spa-pack) using a cable with char-
acteristics not inferior to H 05 VV-F 3x1.5 mm
2
.
Electrical features
Volt Hertz Ampere (k) kW
220-240 ~ 50/60 3.5 (a) ~ 0.7 (b)
(a): a 230 V - (b): power absorption
- It is possible to connect the appliance to an alarm circuit; there
must be, within the area marked with the bell symbol, a cable
with characteristics not inferior to type H 05 VV-F 2x0.75 mm
2
.
Weights
max. weight
at full load
ground
resting surface
ground load
kg m
2
kg/m
2
~ 140 ~ 0.5 ~ 280
- Any panels, or structural parts, where made from conductive
materials, must be connected to the protection circuit (ground
system) and to the equipotential connection.
- Where plastic, wood, etc. materials are used, ensure that they
are certified to be used with electrical installations, even in terms
of flame retardant properties.
- The spa-pack booster kit must be installed according to the in-
structions provided. It is recommended that PVC pipes are used.
Electrical safety
It is the installer’s responsibility to select the materi-
als, considering the way they will be used; to carry out
the installation correctly; and to verify the condition
of the network to which the system will be connect-
ed and its capability to ensure safety in maintenance
and inspection operations.
- The spa-pack booster kit is a class “1” apparatus, so it must be
connected permanently, without intermediate junctions, to the
electrical network and protection circuit (ground system).
The building's electrical system and ground system
must be efficient and must conform to legal regula-
tions and specific national standards.
Where required, appropriate devices must be provid-
ed, which form part of the fixed system, and installed
in compliance with current legislation in force, with
the purpose of disconnecting the appliance from the
mains.
- For connection to the electric mains, you will need to install an
isolating multi-pole switch, which will ensure complete discon-
nection in the instance of a category III over voltage; this device
must be connected to an area that complies with the safety reg-
ulations governing bathroom safety and in any case out of the
reach of the people using the spa.
The appliance must be powered by means of a differ-
ential switch with operating current which does not
exceed 30 mA.
- For the equipotential connection (Standard EN 60335.2.60 )
the installer must use the terminal provided on the spa-pack and
identified by the symbol . In particular, it is necessary to ensure
that all the surrounding metal masses are equipotential, such as
water pipes, gas pipes, perimetric metal boards, etc.
ATTENTION! Before carrying out any maintenance
operation, disconnect the appliance from the power
supply line.