Jackson ECOLAB ES-2000 Installation & Operation Manual Download Page 68

Page: 68 / 91

ES-2000 & ES-4000 Series Installation/Operation Manual 7610-011-35-10

Issued: 10-29-2007 Revised: N/A

SECTION 6: PARTS SECTION

ES-2000-CS INCOMING PLUMBING ASSEMBLY & MISC. PARTS

Y-Strainer, 1/2"

Ecolab No.: 96027024

Mfg. No.: 04730-217-01-10

Nipple, 1/2” Close

2 Per

Ecolab No.: 85141208

Mfg. No.: 04730-207-15-00 Tee, 1/2" X 1/2" X 1/4"

Ecolab No.: N/A
Mfg. No.: 04730-002-22-56

Nipple, 1/2" x 2" Brass

Ecolab No.: 85141224

Mfg. No.: 04730-207-19-00

Valve, Solenoid 1/2" 115V
Ecolab No.: 96580683
Mfg. No.: 04810-100-12-18

Elbow, 1/2”, 90° Street

Ecolab No.: 86075000

Mfg. No.: 04730-206-08-00

Plug, Heyco
2 per (Not Shown)
Ecolab No.: 96024567
Mfg. No.: 05975-011-47-81

Bracket, Plumbing Support

(Not Shown)

Ecolab No.: 96028816

Mfg. No.: 05700-002-28-95

Plug, 1/4” Brass

Ecolab No.: 86135019

Mfg. No.: 04730-209-01-00

Sump Strainer Weldment

Ecolab No.: 96028709

Mfg. No.: 05700-002-11-63

Drain Stopper Weldment
Ecolab No.: 96028691
Mfg. No.: 05700-002-08-44

Drain Stopper
Ecolab No.: 96557475
Mfg. No.: 05700-121-35-54

Rack Guide

Ecolab No.: 96558655

Mfg. No.: 05700-001-28-19

Locknut, 10-24 with Nylon Insert
Ecolab No.: 88429063
Mfg. No.: 05310-373-01-00

Complete Rack Assembly

Ecolab No.: N/A

Mfg. No.: 05700-002-01-00

Rack Weldment
Ecolab No.: 96028147
Mfg. No.: 05700-002-01-01

Screw, 10-24 x 1/2” Long
Ecolab No.: 88120746
Mfg. No.: 05305-173-18-00

Summary of Contents for ECOLAB ES-2000




























































































Search results

Summary of Contents for ECOLAB ES-2000

Reviews:

Related manuals for ECOLAB ES-2000

Brands by name

Popular brands

Jackson ECOLAB ES-2000, Installation & Operation Manual

Search results

Summary of Contents for ECOLAB ES-2000

Reviews:

Related manuals for ECOLAB ES-2000

Brands by name

Popular brands