Jackson MSC JP-24F Service Manual Download Page 38

Page: 38 / 64

ILLUSTRATED PARTS LIST

The following assemblies are illustrated in this order:

Section

Page

TUB AND FRAME ASSEMBLY

Kick Plate, Top, Side, Panel and Machine Assembly

Shroud and Machine Assembly

Tub and Frame Assembly

Weldment, Left Frame

Weldment, Right Frame

DOOR, HINGE, STOP AND LATCH ASSEMBLY
Door, Hinge, Stop and Latch Assembly

Latch Assembly

Door Assembly

CONTROL PANEL AND KICK PLATE ASSEMBLY
Control Panel and Kick Plate Assembly

Control Panel Assembly

ELECTRICAL
Electrical Panel

NTERNAL MACHINE

Booster Tank to Hub and Hood Assembly

Wash Tank Heater

Weldment, Strainer

Weldment, Tube Rinse Stiffner

Bearing Assembly

Wash Arm/Hub Assembly

Rinse Arm Assembly

Wash Pump to Tub/Hood Assembly

PUMP AND MOTOR
Pump and Motor Assembly

Drain Plumbing to Motor/Wash Tank Assembly

INTERNAL PLUMBING
Rinse Plumbing Assembly

Drain Valve Assembly

INCOMING PLUMBING ASSEMBLY
Incoming Plumbing Assembly JP-24B

Incoming Plumbing Assembly JP-24LT

Solenoid Valve Assembly

ACCESSORIES

DECALS AND LABELS

58-59

Summary of Contents for JP-24F

































































Search results

Summary of Contents for JP-24F

Reviews:

Related manuals for JP-24F

Brands by name

Popular brands

Jackson MSC JP-24F, Service Manual

Search results

Summary of Contents for JP-24F

Reviews:

Related manuals for JP-24F

Brands by name

Popular brands