manualshive.com logo in svg

JAC HFC4DA1-2C, Maintenance Manual

The JAC HFC4DA1-2C Maintenance Manual is a comprehensive guide to ensure proper care and maintenance of your vehicle. This manual covers all necessary procedures and maintenance schedules to keep your vehicle in top condition. Download your free copy from manualshive.com and keep your vehicle running smoothly.

Share
Download
background image

FAX

FAX

FAX

FAX Front

Front

Front

Front Suspension

Suspension

Suspension

Suspension

-

129

129

129

129

-

Removal

Removal

Removal

Removal and

and

and

and Installation

Installation

Installation

Installation of

of

of

of Front

Front

Front

Front Shock

Shock

Shock

Shock Absorber

Absorber

Absorber

Absorber

Removal
1.

Loosen wheel nuts, lift the vehicle and remove
wheels.

2.

Remove the brake hose from the shock absorber.

3.

Support the lower swing arm.

4.

Support the wheel hub assembly.

5.

Remove the shock absorber from the cab.

�

Remove the cap.

�

Remove nuts and washers for fastening the
central shaft with an L-shaped allen wrench.

�

Remove the disc washer.

6.

Remove the shock absorber form the steering
knuckle.

Installation
7.

Install the shock absorber onto the steering
knuckle.

8.

Apply some soap solution onto the inner side of the
shock insulator and top of the shock absorber.

9.

Install the shock absorber in place.

Summary of Contents for HFC4DA1-2C


































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for HFC4DA1-2C

M.T.H. RailKing RKS SD70ACE Operator'S Manual preview
RailKing RKS SD70ACE
Brand: M.T.H. Pages: 12
Parker PGM 500 Series Service Manual preview
PGM 500 Series
Brand: Parker Pages: 32
Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual preview
HP525 EFI Bravo Sterndrive Series
Brand: Mercury Racing Pages: 147
Hoval DRHX-1055 MAD5 Manual preview
DRHX-1055 MAD5
Brand: Hoval Pages: 12
ABB VTC254-23 Operation Manual preview
VTC254-23
Brand: ABB Pages: 215
GAS GAS 2005 ENDUCROSS EC 125 Parts List preview
2005 ENDUCROSS EC 125
Brand: GAS GAS Pages: 50
Nice To-Max Pro Instructions And Warnings For Installation And Use preview
To-Max Pro
Brand: Nice Pages: 21
Nice Era-Era Zero E LH Instructions And Warnings For Installation And Use preview
Era-Era Zero E LH
Brand: Nice Pages: 32
TCF DCRD Installation, Operation & Maintenance Manual preview
DCRD
Brand: TCF Pages: 16
Champion 100738 Operator'S Manual preview
100738
Brand: Champion Pages: 72
Clinton 500 Service Manual preview
500
Brand: Clinton Pages: 7
Hacker A30 Glider Manual preview
A30 Glider
Brand: Hacker Pages: 10
Hacker Motor A50 14-Pole V2 Manual preview
A50 14-Pole V2
Brand: Hacker Motor Pages: 4
Champion C46565 User Manual preview
C46565
Brand: Champion Pages: 22
Vanguard 10V000 Operator'S Manual preview
10V000
Brand: Vanguard Pages: 136
Honda GXE2.0S Manual preview
GXE2.0S
Brand: Honda Pages: 59
sati GB755 Installation And Maintenance Instructions Manual preview
GB755
Brand: sati Pages: 19
HELIX DM422 User Manual preview
DM422
Brand: HELIX Pages: 18

Brands by name

Popular brands

Load more brands