JAC HFC4DA1-2C Maintenance Manual Download

Page: 531 / 801

BR Brake

Brake

Brake System

System

- 53-

Removal/Installation

During the installation of new brake lining, please
remove the snap ring of brake lining from the brake
caliper.

Clear any dirt within the mounting areas.

Installation
1.

Install new snap ring onto new brake lining.

Check if two brake linings are of the same type.

During the installation of new brake lining, please
remove the interleaving paper from the acoustic
lining.

Reinstall inner/outer brake lining.

Reinstall the brake caliper assembly:

�

Install the brake caliper assembly.

�

Install the guide pin bolt of brake caliper.

�

Install the plastic cap of brake caliper guide
pin.

Adjust the slider of brake plate.

Reinstall the wheel and lower the vehicle.

Check the brake fluid level of master cylinder. If
insufficient, please add brake fluid to the standard
position.

Summary of Contents for HFC4DA1-2C


































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HFC4DA1-2C

Reviews:

Related manuals for HFC4DA1-2C

Brands by name

Popular brands

JAC HFC4DA1-2C, Maintenance Manual

Search results

Summary of Contents for HFC4DA1-2C

Reviews:

Related manuals for HFC4DA1-2C

Brands by name

Popular brands