JAC HFC4DA1-2C Maintenance Manual Download | Manualshive

Page: 147 / 801

background image

Maintenance manual for sunray hfc4da1-2c china-IV diesel engines

148

10.

DTC

P0251

The control line of fuel level control unit is open.

P0252

The ECU internal driver module of fuel level control unit is overheating.

P0253

The control line of fuel level control unit is short to ground.

P0254

The control line of fuel level control unit is short to high level.

Fault Description:

The fuel metering unit is for adjusting the fuel supply and the fuel pressure. When the control coil

of metering unit is off, the inlet fuel metering proportional valve of the unit shall be closed, cutting off the fuel
supplied to the high pressure fuel pump plunger component. When the control coil of metering unit is electrified, the
ECU shall change the fuel inlet sectional area of metering component via pulse signal according to the actual demand,
through which, the fuel supplied to the high pressure fuel pump plunger component shall be changed. If the fuel
metering control signal voltage detected by ECU is abnormal, the DTC shall be generated.

Diagnosis Hint:

The metering component is mounted at the fuel inlet of high pressure pump. The engine’s fuel

supply shall be affected directly by the opening sectional area of the fuel metering unit control valve. Provided that the
fuel metering unit control line is normally connected, monitor the engine fuel supply amount and pressure while
moving relevant connector and wire to check if any fault is triggered. If any, the indication of fault diagnostic unit
shall change. This is help for locating the intermittent failure.

The intermittent failure may be caused by poor contact of control part. As for poor contact between ECU and fuel
metering unit, please check the ECU harness connector for the following conditions:

−

Loose terminal

−

Poor matching and connection

−

Breakage of keeper

−

Distortion or damage of terminal

−

Poor contact between terminal and wire

Check the harness for any damage. If the harness appears normal, observe the fuel pressure indicated on the diagnostic
tool while moving relevant connector and harness of fuel metering unit. If the pressure indication changes, there must
be failure in that part.

Terminal ECU

A19

Power supply terminal of fuel metering unit

A49

Signal terminal of fuel metering unit

Control of fuel metering unit

Fuel metering unit

«
...
145
146
147
148
149
...
»

Summary of Contents for HFC4DA1-2C


































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for HFC4DA1-2C

Brand: Kohler Pages: 4

Brand: Polini Pages: 34

Brand: FAAC Pages: 124

Johnson BJ25E4SUC

Brand: BRP Pages: 265

Brand: Briggs & Stratton Pages: 14

Brand: Kohler Pages: 176

Brand: Champion Power Equipment Pages: 29

Brand: MTU Pages: 239

RADIOMODULE 2G4

Brand: Grundfos Pages: 76

Brand: Rotax Pages: 84

Brand: Rotax Pages: 166

Enduro RR 350 2015

Brand: Beta Pages: 158

Brand: DANA Pages: 2

Brand: DANA Pages: 3

Brand: DANA Pages: 3

Brand: O.S. engine Pages: 20

MAX-12CV Series

Brand: O.S. engine Pages: 30

Brand: O.S. engine Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands